|
|
Education and Career Forum
|
|
|
|
| 3rd April 2012 07:47 PM | ||
| Unregistered |
Re: Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? what are the important qualification in machanical students? |
|
| 27th July 2011 10:12 PM | ||
| Unregistered |
Re: Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? the typical set of mechanical working drawings includes |
|
| 8th December 2010 08:31 PM | ||
| vike |
Re: Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? Quote:
The HPCL exam for the officer trainee exam is a objective test followed by a personal interview for those who qualify the written test. The objective test consist of two parts. Part I is General Aptitude test which include IQ test, Quantitative aptitude and English language test. Part II is Technical paper which is based on the qualifying degree. The exact syllabus of the exam is not published by HPCL because this type exam include questions from the entire engineering syllabus(for engineer section for HR it would their course). In these type of exams companies don't provide syllabus for the written test because they try to take those candidates who have good command on the technical knowledge. So, if you want to know the exact syllabus, it's your complete degree. You should prepare the whole course content of your core subjects. eg. Mechanical candidates will be asked questions from mechanical papers only. The written test is objective type so its easy to prepare the entire course content because you do not need to remember all the derivation and explanation sort of stuffs. Just read everything twice-thrice and remember the key points so that you can answer any objective question. The Part I of the test can be prepared only by practice. You can get the practice test from book stores. The aptitude test practice papers are not specifically designed for a particular exam. You can take any practice paper of this kind. For any further formation you can visit http://jobs.hpcl.co.in/Recruit_online/ or www.hindustanpetroleum.com The notification for the same is attached with this message. Find it into the attachments. Thank You |
|
| 4th December 2010 04:55 PM | ||
| RAKESH KUMAR.N |
Re: Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? sectional view 1. This type of section is limited by a break line: A. Removed section B. Revolved section C. Broken-out section D. Half section View Answer Workspace Report Discuss in Forum 2. Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical view of a threaded hole. A. Center line B. Hatch line C. Poly line D. Dimension line View Answer Workspace Report Discuss in Forum 3. The section view drawing in which one fourth of an object has been marked for removal is known as a ________ section. A. full B. half C. quarter D. none of the above View Answer Workspace Report Discuss in Forum 4. In offset sections, offsets or bends in the cutting plane are all: A. 90 degrees B. 180 degrees C. Either 90 or 180 degrees D. 30, 60, or 90 degrees View Answer Workspace Report Discuss in Forum 5. When filling an area with a hatch pattern in AutoCAD the drafter needs to be able to ________. A. see the entire bounding area to hatch B. set Ortho on C. turn ISO grid off D. set the layer to Defpoints test 1 |
|
| 4th December 2010 04:47 PM | ||
| RAKESH KUMAR.N |
Re: Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? this topic contain Mechanical working diagram 1. The typical parts list should include the ________. A. part number B. manufacturing material C. number of parts needed D. all of the above View Answer Workspace Report Discuss in Forum 2. A typical set of mechanical working drawings includes ________. A. exploded assembly B. part details C. parts list D. all of the above View Answer Workspace Report Discuss in Forum 3. The title block used on working drawings should include the ________. A. sheet number B. line type C. layer set D. all of the above View Answer Workspace Report Discuss in Forum 4. One critical issue drafters need to pay close attention to is the ________. A. size of the sheet B. designer's intent C. scale factor D. none of the above View Answer Workspace Report Discuss in Forum 5. In the mechanical design process the first step is to ________. A. brainstorm solutions B. prepare rough sketches C. prepare a budget D. identify the problem 6. The text used on a typical detail sheet should be ________. A. placed horizontally B. in bold text C. in an architectural text style D. none of the above View Answer Workspace Report Discuss in Forum 7. In an exploded assembly drawing it is customary for the drafter to use a ________ line to illustrate how parts fit together. A. Phantom B. hidden C. dashed D. center View Answer Workspace Report Discuss in Forum 8. It is customary for the first sheet of a working drawing set to include ________. A. a parts list B. exploded assembly C. assembled assembly D. all of the above View Answer Workspace Report Discuss in Forum 9. In order to create an accurate assembly drawing the drafter should create the ________ drawings first. A. Detail B. title block C. parts list D. isometric View Answer Workspace Report Discuss in Forum 10. The thread note for a typical bolt will include the ________. A. major diameter of the thread B. material C. center line D. offset distance Best of luck, if you don't find the answer, i will help you out |
|
| 4th December 2010 02:43 PM | ||
| Unregistered |
Syllabus of latest HPCL exam? Important subjects for Mechanical Engineering students? what is the syllabus for latest HPCL exam?what are important subjects for the candidates who belongs to mechanical in engineering stream? |
|
