10th October 2015 01:17 AM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam Which book should I considered for electronics branch nd applied for octt post nd plz tell me cut off marks for general students in latest exam of bhilae..plz rply soon |
8th September 2013 01:30 AM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam What is expected sectional cutoff for sail mt 2013? |
29th March 2013 07:42 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam hi,i want to know about the cut off marks in separate sections of MTT of SAIL? IS THERE ANY CUT-OFF FOR GK SEPARATELY? REPLY ME IN THE FOLLOWING MAIL ADDRESS [email protected] |
17th July 2012 05:28 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam what ll be the expected cutt off for MT (HR) 2012? |
29th May 2012 12:44 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam what is the total no of seats in ET branch? |
22nd April 2012 06:04 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam SYLLABUS for operator cum technician of SAIL Bokaro 2012 |
17th November 2011 02:51 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam Hi, MT 2011.i think cutoff for tech is-65 Non Tech is--60 |
27th October 2011 09:31 PM | |
mukulkarn |
Subjects and cutoff of GAIL entrance exam Hi What is the expected cutoff for GAIL examination.please give your valuable suggestion.. |
18th October 2011 09:05 PM | |
Fraction Down |
Re: Subjects and cutoff of SAIL entrance exam dear friend, According to Steel Authority of India(SAIL) Syllabus there is five section in the examination syllabus:- 1.>Reasoning of 45 marks. 2.>Quantitative of 35 marks. 3.>General English of 35 marks. 4.>General Knowledge of 35 marks. 5.>Technical Aptitude from candidates branch of 100 marks. Total number is 250 marks. Friend,in this examination there is no fixed cut off marks.The Cut off marks totally depends on Question standard and also number of candidate appearing.This cut off marks is select by SAIL entrance exam authority. But my friend ,you can expect more or less 35 marks as cut off marks. best of luck. |
15th October 2011 02:51 PM | |
mukulkarn |
Re: Subjects and cutoff of SAIL entrance exam i have attempted around tech:60 correct english:17 correct maths: 20 correct DI:25 correct GK:19 correct what is my probability to get in.actually i am preparing for CAT so my tech part is not good... please reply must. |
3rd October 2011 05:52 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam what about expected cutoff in sail mt 2011? |
27th September 2011 05:28 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam I can not answer the GK portion much but others portion well. |
25th September 2011 07:50 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam share some questions of today paper |
24th September 2011 09:14 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam thanx for d reply...... |
20th September 2011 11:31 AM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam please tell me the cutt off marks for 2011 mt exam???? |
20th September 2011 01:36 AM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam which book should we prefer for the preparations? specially 4 d general science part. |
16th August 2011 09:18 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam cut off marks mechanical 2010 ? |
27th June 2011 03:53 AM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam do exams are taken according to desired student's graduated department? for example i am from electronics and instrumentation dept. |
5th February 2011 10:34 AM | |
xavi |
Re: Subjects and cutoff of SAIL entrance exam freind hi, --->>sail syllabus contain five section:- Reasoning of 45 marks Quants of 35 marks English of 35 marks G.K of 35 marks and your Technical paper of 100 marks -->Cutt-offs are there for every sections -->35 may be the cutoff mark all the best |
3rd February 2011 08:13 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam Is SAIL entrance exam tougher than IIT? |
24th December 2010 10:15 PM | |
kumarpravir007 |
Re: Subjects and cutoff of SAIL entrance exam the subject for the entrance exam of SAIL entrance exam are : reasoning gk english quant and the technical paper...... and the cut off depends on the paper that is how tough the paper is ......the cut off would go low and if the paper is easy then the cut off would go high ..... so best of luck ... |
24th December 2010 10:11 PM | |
kumarpravir007 |
Re: Subjects and cutoff of SAIL entrance exam the subject for the entrance exam of SAIL entrance exam are : reasoning gk english quant and the technical paper...... and the cut off depends on the paper that is how tough the paper is ......the cut off would go low and if the paper is easy then the cut off would go high ..... so best of luck ... |
21st December 2010 02:42 PM | |
drdo99 |
Re: Subjects and cutoff of SAIL entrance exam friend, some of the important questions asked are as follows: 1. Two free parallel wires carrying current in the opposite directions (a) Attract each other (b) Repel each other (c) Do not effect each other (d) Get rotated to be perpendicular to each other Ans.(b) 2. All the magnetic materials looses their magnetic property when (a) Dipped in water (b) Dipped in oil (c) Brought near piece of iron (d) Strongly heated Ans.(d) 3. Potassium paramagnet is used for (a) Dechlorination (b) Improving colour (c) Reducing acidity (d) Reducing hardness Ans.(b) 4. Which of the following material has the highest carbon percentage? (a) Cast iron (b) Mild steel (c) High carbon steel (d) Stainless steel Ans.(a) 5. Which of the following paints is most fire resistant (a) Bituminous paint (b) Asbestos paint (c) Aluminum paint (d) Synthetic paint Ans.(b) 6. The gas which is mainly responsible for the explosion in sewers is (a) Methane (b) Ethane (c) Ammonia (d) Carbon- monoxide Ans.(d) 7. The Wind screen of car made of (a) Sheet glass (b) Wired glass (c) Laminated glass (d) Flint glass Ans.(c) 8. Which of the welding process is used for welding of structures? (a) Gas welding (b) Fusion welding (c) Thermic welding (d) Arc welding Ans.(d) 9. In a d.c generator, following losses will be minimum (a) Copper loss (b) Iron loss (c) Friction loss (d) Shunt field copper loss Ans.(b) 10. Corona loss is less when the shape of the conductor is (a) Circular (b) Flat (c) Oval (d) Independent of shape Ans.(a) 11. The core of the transformer is assembled with laminated sheet so as to reduce (a) Hysteresis loss (b) Copper loss (c) Magnetic noise (d) Eddy current loss Ans.(d) 12. Which of the following instrument is used for measuring the rate of flow of liquid of pipes (a) Hydro meter (b) Venturi meter (c) Viscometer (d) Falter pump Ans.(b) 13. The proper use of lubricants cannot reduce (a) Static friction (b) Inertia (c) Sliding friction (d) Rolling friction Ans.(b) 14. Infra red radiation can be detected by (a) Spectrometer (b) Pyrometer (c) Nanometer (d) Photometer Ans.(b) 15. Which of the following is used in optical fibers (a) Total internal reflection (b) Scattering (c) Diffraction (d) Refraction Ans.(a) 16. Metal attains super- conduction properties below the temperature of (a) 0 deg K (b) 100 deg C (c) 100 deg K (d) 10 deg K Ans.(d) 17. Powder clinges to the skin because of following property (a) Adhesion (b) Cohesion (c) Surface tension (d) Capillary action Ans.(a) 18. The sparking at the brushes in the d.c generator is attributed to (a) Quick reversal of current (b) Reactance voltage (c) Armature reaction (d) High resistance of the brushes Ans.(c) 19. D.C series motor should always be started with load because (a) At no load it will rotate at dangerously high speed (b) At no load it will not develop high starting torque (c) It cannot start without load (d) It draw a small amount of current at no load Ans.(a) 20. A tunnel diode is (a) High resistivity p-n junction diode (b) A slow switching device (c) An amplifying device (d) A very heavily doped p-n junction diode Ans.(d) 21. The effective channel length of a MOSFET in saturation decreases with increase in (a) Gate voltage (b) Drain voltage (c) Source voltage (d) Body voltage Ans. (b) 22. The ON voltage and forward breakover voltage of an SCR depends on the (a) Gate current alone (b) Band gap of the semiconductor alone (c) Gate current and the semiconductor band gap respectively (d) Semiconductor bandgap and the gate current respectively Ans.(c) 23. Negative feedback in amplifier (a) Improves the signal to noise ratio at the input (b) Improves the signal to noise ratio at the output (c) Does not affect the signal to noise ratio at the output (d) Reduce the distortion. Ans.(b) 24. An ideal Op- Amp is an ideal (a) Voltage controlled current source (b) Voltage controlled voltage source (c) Current controlled current source (d) Current controlled voltage source Ans.(b) 25. One of the following types of noise becomes of great importance at high frequencies. It is the (a) Shot noise (b) Random noise (c) Impulse noise (d) Transit- time noise Ans.(d) 26. Piezoelectricity effect is the polarization of a dielectric under the influence of (a) Light (b) Mechanical stress (c) Electrical stress (d) Heat Ans.(b) 27. Entropy of mixture of two gases after sudden mixing is (a) Greater than (b) Less than (c) Same as sum of entropy of individual gases (d) Unpredictable Ans.(a) 28. If air filter is removed in a petrol engine, the air/fuel ratio will (a) Increase (b) Decrease (c) Increase and decrease (d) Remains unchanged Ans.(a) 29. In a two stage compression , inter -cooling is used for (a) Reducing work of compression in the first stage (b) Reducing temperature in the first stage (c) Reduced work in the second stage (d) Reducing work and temperature in the second stage Ans.(d) 30. Which component of refrigeration system controls the flow of refrigerant (a) Expansion valve (b) Condenser (c) Compressor (d) Evaporator Ans.(a) 31. Laser beam welding has widest application in (a) Mass production in heavy industry (b) Jobbing industry (c) Electronic industry (d) Structure and bridge work Ans.(c) 32. In Equation x-2y+3z=0 and 2x+5y+3z=0, y equals (a) 0 (b) 1 (c) 2 (d) 3 Ans.(a) 33. If a system of equation has one or more solution it is called (a) Compatible (b) Consistent (c) Homogeneous (d) Simultaneous Ans.(b) 34. In a microprocessor the register which holds the address of the next instruction to be fetched is (a) Accumulator (b) Program counter (c) Stack pointer (d) Instruction register Ans.(b) 35. The mnemonics used in writing a program is called (a) Assembly language (b) Fetch cycle (c) Microinstruction (d) Object program Ans.(a) 36. For which of the following devices, is DMA the most suitable (a) Keyboard (b) Mouse (c) Joy stick (d) Hard stick Ans.(d) 37. In real time operating system, which of the following is the most suitable scheduling scheme? (a) Round robin (b) First come first served (c) Random scheduling (d) Preemptive Ans.(d) 38. In client –server system , data is usually stored on the (a) Server (b) Client (c) Network (d) None of the above Ans.(a) 39. Identify the natural (a) LISP (b) PROLOG (c) Both (a) and (b) (d) Neither (a) and (b) Ans.(c) 40. An interrupt that can temporarily ignored by the counter is known as (a) Vectored interrupt (b) Non – maskable interrupt (c) Maskable interrupt (d) Low priority interrupt Ans.(c) you should also practise,g.k,aptitude. |
19th December 2010 09:29 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam I don%u2019t know what would be the cutoff but I think it will be similar to : Marketing : 55 GS : 10 Quant : 11 English : 15 Reasoning : 5 which i found on sorapedia.com |
19th December 2010 05:10 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam When will be the exam be conducted on 2011 |
13th December 2010 06:54 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam tell me cutoff of each section of et branch |
25th November 2010 11:01 AM | |
vikash_study |
Re: Subjects and cutoff of SAIL entrance exam wants questions for computer science branch and other formats for this exam |
18th November 2010 12:57 PM | |
saswat |
Re: Subjects and cutoff of SAIL entrance exam questions for computer science branch comes from which topic ...want to know maths is included or not ...and wich subjects are covered ??????????? |
18th November 2010 07:27 AM | |
asahu47 |
Re: Subjects and cutoff of SAIL entrance exam ihii Subjects of SAIL entrance exam For sail syllabus contain five section:- Reasoning of 45 marks Quants of 35 marks English of 35 marks G.K of 35 marks and your Technical paper of 100 marks and prepare according to that. consentrate on ur fundamentals///and on ur branch subjects. good luck. |
17th November 2010 10:51 PM | |
Unregistered |
Re: Subjects and cutoff of SAIL entrance exam howmany students give sail exam and howmany got selected in them??? |
17th November 2010 08:42 PM | |
rmani9896 |
Re: Subjects and cutoff of SAIL entrance exam I want cutoff marks of sail question paper of each section |
15th November 2010 11:52 AM | |
priyanka_swengg |
Re: Subjects and cutoff of SAIL entrance exam For sail syllabus contain five section:- Reasoning of 45 marks Quants of 35 marks English of 35 marks G.K of 35 marks and your Technical paper of 100 marks and prepare according to that. |
14th November 2010 07:48 PM | |
SATISH87 |
Subjects and cutoff of SAIL entrance exam What are the subjects of SAIL entrance exam? Also tell me the related cutoff for this exam i.e. minimum marks to qualify this exam. |