Education and Career Forum

respected sir/madam,

Im Nagaratinam.I have applied for BEL recuitment drive for electronics.
.I want to know, if there is any syllabi to be followed ? and if so, can u please send me. Also Im in need of model question papers.so, I request u to kindly send the syllabi and model question papers.

hiii.......this pdf contains different BEL papers.....follow this u can get success in the exam......it contains model papers.....

Originally Posted by Unregistered

respected sir/madam,

Im Nagaratinam.I have applied for BEL recuitment drive for electronics.
.I want to know, if there is any syllabi to be followed ? and if so, can u please send me. Also Im in need of model question papers.so, I request u to kindly send the syllabi and model question papers.

Hi
Firstly I want to say that you have choosen good company but you have to hard work for their written test.
I have some information related to their test because one of my friend clear that exam.
*Written test is of 2.5hours.

*30 question- Aptitude

*3 question-Passage

*Some more topics which you have to learn.
*Data interpretation
*General knowledge
*Compound interest
*Height and distance
*Solid state and electronics
*Circuit theory
*Network Theorems
*Digital signal processing
*Microprocessors
You have to prepare for all the above topics.

And you can download papers from below givensite.
http://www.placementpapers.net/helpingroot/BEL/BEL_Placement_Paper
http://forums.sureshkumar.net/bel-placement-papers/17713-bbb-placement-paper-1-a.html
Goodluck

hi friend
you can get the model question paper of the bel exam on the following website,the list of the sites are as follow
1.www.placementpapers.net

2.www.forums.sureshkumar.net

3.freshersworld.com

Originally Posted by Unregistered

respected sir/madam,

Im Nagaratinam.I have applied for BEL recuitment drive for electronics.
.I want to know, if there is any syllabi to be followed ? and if so, can u please send me. Also Im in need of model question papers.so, I request u to kindly send the syllabi and model question papers.

Dear friend there are mainly three subjects which is asked in exams.
First is Quantitative Ability
Second is Verbal Ability
Third is Data Interpretation.

If you have command over these three subjects then you will surely get succeed.

For model question papers visit the site of placement papers.

Best of luck

Dear friend,
For BEL model question papers for electronics engineering,
you go through the website:www.forums.sureshkumar.net

hello,
one can download the BEL model question papers from this post ......

it is in the pdf format .......

hope it helps you.....

best of luck

hey friend i have attached the question paper for the BEL for electronics engineering.

download the file and prepare well for the exam.

all the best

of both current and previous semesters. 8.2 Three tests each carrying ... semester examinations of the semester in question, through the Head of the ...
http://www.diasindia.org/dias/forms/brochure.pdf
.../cad2008...Show Online Download
3.18 Each question shall have four choices for answers, out of which only one ... related to admission shall be notified in five news papers of the State of Goa, ...
http://www.dtegoa.gov.in/cad2008/g2cet2008.pdf

hello friend,
i will give you the link to download the questio papers k:
http://www.ziddu.com/download/10637522/BELBHELExamPapers.pdf.html#more
All The Best.

i am soumya. plz send BEL SYLLABUS for 2011 for electronics and telecommunication.ALSO SEND MODEL QUESTIONS WITH SOLUTIONS.
My email ID:[email protected]

plz send BEL SYLLABUS for 2010 for ECE dept

Dear Sir/Mam
This geeta from gulbarga sir/mam i applied for post of technician 'c' so pls praved the model sovld questions peper of
electronic mechanic my email ID is [email protected] so pls do the needful

Thank you
Geeta

http://entrance-exam.net/bel-placement-papers/

hello, how can i get the detailed question paper of bel?

Dear Sir/Madam,
Please send BEL 2011 Exam Syllabus for Electrinics & Commn(BE)

hi,
plz send me syllabus for electronics

i am Praveenjyot Singh.I have applied for BEL recuitment drive for computer science.
I want to know, if there is any syllabi to be followed ? and if so, can u please send me. Also Im in need of model question papers.so, I request u to kindly send the syllabi and model question papers
[email protected]

i am praveen i applied for BEL examination 2011 i need a model question paper in the stream of electronics plz send in [email protected]

Dear Sir/Madam,
Please send BEL 2011 Exam Syllabus for Electrinics & Commn(BE) & previous year question paper

i am applying for the PROBATIONARY ENGINEERS 2011 post
please tell me the previous papers

i am applying for the BEL company for the PROBATIONARY ENGINEERS 2011 post
please tell me the previous papers

hi i applied for BEL entrance exam..i dont have any model question for CSE.plz send any link or file which will be very useful for my exam

Hi. I have applied for PROBATIONARY ENGINEERS in BEL. Please let me know the areas I need to concentrate for getting this job. I 'm 2010 batch student and my stream is ECE(Electronics and Communication).

please send syallabus for bel exam for electronics stream

Originally Posted by Bharaji

Dear Sir/Madam,
Please send BEL 2011 Exam Syllabus for Electrinics & Commn(BE)

study all syllabi...............

please send me link or file electronice engineeering

please send me link or file syllabus electronics and engineering

hallo sir
this is shashikant gupta. i need previous year question paper of bel for mechanical engineering. plz send it to me as soon as possible. my email id is [email protected].

thank u

Hi sir im anjaly.I applied for BEL exam.Can u plz send me previous year question paper.My mail id is [email protected]

hi i am abirami i am computer science student...i applied for bell so would u pls send syllabus and sample question paper to my mail [email protected]

sir,
please send me BEL probationary engineers model question papers(electronics and communication engineering)
and syllabus to my mail [email protected]

From I can get questions papers of various higher level engineering exams?

i want to join bel.now i am doing my work in bel. only for training.but i want permanent job.how to prepare my exam.pls tell me. i completed my diploma in ece(90%).pls give me answer.

Hello..
Here are the details of 2011 BEL Placement Paper

1. In which of the following movements ‘Vande Mataram’ was adotped for the first time as a slogan for agitation?

(A) Revolt of 1857
(B) Partition of Bengal in 1905
(C) Non-cooperation Movement in 1922
(D) Quit India Movement in 1942

2. Who warned Gandhiji not to encourage fanaticism of Muslim religious leaders and their followers?

(A) Agha Khan
(B) AjmaI Khan
(C) Hasan Imam
(D) Mohammad Ali Jinnah

3. Which one of the following is not correct about the Congress Session.of Lucknow, 1916?

(A) Ambika Charan Majumdar was not the president of this session
(B) In this session the reunion between the liberal and the extremist was established
(C) Mahatma was apprised the problems of the peasants Champaran for the first time
(D) None of the above

4. Kanpur conspiracy case was against the leaders of?

(A) Khilafat Movement
(B) Non-cooperation Movement
(C) Communist Movement
(D) Revolutionary Movement

5. In India “Currency Notes issue system” is based on?

(A) Minimum reserve system
(B) Proportional reserve system
(C) Fixed exchange rate system
(D) Full convertibility system

6. ‘Disguised’ unemployment means?

(A) Persons with no jobs
(B) Unemployment among house wives
(C) Unemployment among per sons above 60 years pf age
(D) Employment of more persons in a job which lesser number of persons can perform

7. Which of the following statements are true about the income tax in India?

1. It is a progressive tax,
2. It is a direct tax.
3. It is collected by the Government.
4. It is a proportional tax Select the correct answer from the code given below

Codes:
(A) 1 only
(B) 1 and 2 only
(C) 1,2and3only
(D) 2, 3 and 4 only

8. ‘SIDBI’ has been established to-

(A) Finance small scale industries
(B) Finance cottage industries
(C) Finance large scale industries
(D) Finance public sector under takings

9. Gangubai Hangal, who died a few months ago, was a?

(A) Classical singer
(B) Dancer
(C) Painter
(D) Sitar player

10. Deep Joshi has recently been given Raman Magsaysay Award in the category of?

(A) Government service
(B) Public service
(C) Community leadership
(D) Emergent leadership

11. The missing number in the following series: 5,10,13,26,29, 58, 61,…Is?

(A) 122
(C) 128
(B) 125
(D) 131

12. If 2 jeans and 3 shirts cost Rs. 4,000 and jeans and 2 shirts cost Rs. 3,500, how much does a jeans cost?

(A) Rs. 1,500
(B) Rs 1,000
(C) Rs. 500
(D) Rs. 2,000

13. Which one of the following expresses error in computer data?

(A) chip
(B) byte
(C) bug
(D) bit

14.Assertion (A) Graphite is a good lubricant. Reason (R) Graphite is good conductor of electricity. Select the correct answer from the codes given below Codes:

(A) Both (A) and (R) are true and (A) is the correct explanation of (A)
(B) Both (A) and (A) are true but (H) is not the correct explanation of (A)
(C) (A) is true but (R) is false
(D) (A) is false but (A) is true

15. Acid rain is caused by pollution ot environment by?

(A) Carbon dioxide and Nitrogen
(B) Carbon monoxide and Carbon dioxide
(C) Ozone and Carbon dioxide
(D) Nitrous oxide and Sulphur dioxide


16. The professional printed circuit board generally use the following as the raw material:

1.Paper base bakelite copper clad sheet
2. Glass epoxy copper clad sheet
3.Tin plated Nylon sheet
4. Silver plated pyrex sheet

17. Many switch contacts use silver as the material because

1. It is a good electrical conductor with low contact resistance
2. Silver does not tarnish
3. It is easily shaped as per requirement
4. It is very hard and does not wear off


18. A resistance of approximate value 85W is to be measured by using an ammeter of range 0-1 A having a resistance of 20 W and voltmeter of range 0-50V having a resistance of 5000W. Two arrangement for the measurement are shown in the figure below. Which method would you recommend?

1. Method X
2. Method Y
3. Either X or Y
4. Neither X nor Y


19. The value of capacitance across points A & B in the circuit shown below is (in microfarads)

a. .3 b. 1 c. 0.67 d. 0.33

20. It is proposed to fabricate a simple Ohm meter for measuring resistor values. A milliammeter with an internal resistance of 50 W is available. Choosing a configuration using a 3 V battery, a large resistance and the ammeter in a loop, the unknown resistor is proposed to be measured by noting the current initially and then connecting the unknown resistor across the ammeter. If the ratio of the two current is 2, what is the value of the unknown resistor (rn W ) ?

a. 3000 b. 150 c. 100 d. 50

21.The current I flowing into the branch indicated by an arrow in the circuit shown is equal to


a. 2 Amp b. 0.5 Amp c. 1 Amp d. 0.25 Amp

22. For the circuit shown, the maximum power is delivered to the load resistance RL when the value of Rg is

a. 2 ohms b. zero c. 10 ohms d. infinity

23. A signal generator is available in the laboratory, which is in good condition except for the attenuator dial which has got displaced. In order to calibrate this, a high frequency oscilloscope is available. At a particular setting of the knob an open circuit voltage of 450 mV rms is measured. If the impedance of the generator is 50 ohms, the setting of the attenuator dial is to be adjusted for

a. 6 dBm b. 1 dBm c. 0 dBm d. 10 dBm

24. The relation Loge (X + Loge (1 + X) = 0 also means that

1. X2 + X + 1 = 0

2. X2 + X - 1 = 0

3. X2 + X + e = 0

4. X2 + X – e = 0

25. The Laplace transform of the function f(t) = cos wt is

1. w/(s2 + w2)

2. s2/(s2 - w2)

3. w2/(s2 + w2)

4. s/(s2 + w2)

26. If a = b = c, one value of X which satisfies the equation

=0 is given by

a. x=a b. x=b c. x=c d. x=0

27. An LC oscillator is being analysed. If the LC tank circuit (with quality factor = Q) is isolated from the amplifying device, the impedance at the resonant frequency as measured looking into the amplifier will be

1. Q r [LC]1/2

2. ½ rp r [LC]1/2

3. – Q r[LC]1/2

4. Q r [LC]1/2


28. A battery eliminator is required to be constructed and an assortment of rectifiers, resistors and capacitors is available. However, the step down transformer available has no center tap. The following configurations for the rectifier are feasible. The one giving the lowest ripple will be

1. Full wave rectifier
2. Half wave rectified
3. Bridge rectifier
4. None

29. Chokes used in rectifier filter circuits are wound on a core with a small air gap. This is done in order to

1. Get as high an inductance as possible
2. Prevent saturation of the core
3. Absorb the ripple effectively
4. Prevent loading the transformer

30. An integrated circuit linear regulator is used at the output of a power supply having a ripple of 1 V rms. Assuming that the IC represents a typical design generally available, the output rms ripple to be expected will be

a.. 0.1 V rms b. 0.1 mV c. 100 mV d. 1.0 V rms

best of luck.......

Hello..
Here are the details of 2011 BEL Placement Paper

1. In which of the following movements ‘Vande Mataram’ was adotped for the first time as a slogan for agitation?

(A) Revolt of 1857
(B) Partition of Bengal in 1905
(C) Non-cooperation Movement in 1922
(D) Quit India Movement in 1942

2. Who warned Gandhiji not to encourage fanaticism of Muslim religious leaders and their followers?

(A) Agha Khan
(B) AjmaI Khan
(C) Hasan Imam
(D) Mohammad Ali Jinnah

3. Which one of the following is not correct about the Congress Session.of Lucknow, 1916?

(A) Ambika Charan Majumdar was not the president of this session
(B) In this session the reunion between the liberal and the extremist was established
(C) Mahatma was apprised the problems of the peasants Champaran for the first time
(D) None of the above

4. Kanpur conspiracy case was against the leaders of?

(A) Khilafat Movement
(B) Non-cooperation Movement
(C) Communist Movement
(D) Revolutionary Movement

5. In India “Currency Notes issue system” is based on?

(A) Minimum reserve system
(B) Proportional reserve system
(C) Fixed exchange rate system
(D) Full convertibility system

6. ‘Disguised’ unemployment means?

(A) Persons with no jobs
(B) Unemployment among house wives
(C) Unemployment among per sons above 60 years pf age
(D) Employment of more persons in a job which lesser number of persons can perform

7. Which of the following statements are true about the income tax in India?

1. It is a progressive tax,
2. It is a direct tax.
3. It is collected by the Government.
4. It is a proportional tax Select the correct answer from the code given below

Codes:
(A) 1 only
(B) 1 and 2 only
(C) 1,2and3only
(D) 2, 3 and 4 only

8. ‘SIDBI’ has been established to-

(A) Finance small scale industries
(B) Finance cottage industries
(C) Finance large scale industries
(D) Finance public sector under takings

9. Gangubai Hangal, who died a few months ago, was a?

(A) Classical singer
(B) Dancer
(C) Painter
(D) Sitar player

10. Deep Joshi has recently been given Raman Magsaysay Award in the category of?

(A) Government service
(B) Public service
(C) Community leadership
(D) Emergent leadership

11. The missing number in the following series: 5,10,13,26,29, 58, 61,…Is?

(A) 122
(C) 128
(B) 125
(D) 131

12. If 2 jeans and 3 shirts cost Rs. 4,000 and jeans and 2 shirts cost Rs. 3,500, how much does a jeans cost?

(A) Rs. 1,500
(B) Rs 1,000
(C) Rs. 500
(D) Rs. 2,000

13. Which one of the following expresses error in computer data?

(A) chip
(B) byte
(C) bug
(D) bit

14.Assertion (A) Graphite is a good lubricant. Reason (R) Graphite is good conductor of electricity. Select the correct answer from the codes given below Codes:

(A) Both (A) and (R) are true and (A) is the correct explanation of (A)
(B) Both (A) and (A) are true but (H) is not the correct explanation of (A)
(C) (A) is true but (R) is false
(D) (A) is false but (A) is true

15. Acid rain is caused by pollution ot environment by?

(A) Carbon dioxide and Nitrogen
(B) Carbon monoxide and Carbon dioxide
(C) Ozone and Carbon dioxide
(D) Nitrous oxide and Sulphur dioxide


16. The professional printed circuit board generally use the following as the raw material:

1.Paper base bakelite copper clad sheet
2. Glass epoxy copper clad sheet
3.Tin plated Nylon sheet
4. Silver plated pyrex sheet

17. Many switch contacts use silver as the material because

1. It is a good electrical conductor with low contact resistance
2. Silver does not tarnish
3. It is easily shaped as per requirement
4. It is very hard and does not wear off


18. A resistance of approximate value 85W is to be measured by using an ammeter of range 0-1 A having a resistance of 20 W and voltmeter of range 0-50V having a resistance of 5000W. Two arrangement for the measurement are shown in the figure below. Which method would you recommend?

1. Method X
2. Method Y
3. Either X or Y
4. Neither X nor Y


19. The value of capacitance across points A & B in the circuit shown below is (in microfarads)

a. .3 b. 1 c. 0.67 d. 0.33

20. It is proposed to fabricate a simple Ohm meter for measuring resistor values. A milliammeter with an internal resistance of 50 W is available. Choosing a configuration using a 3 V battery, a large resistance and the ammeter in a loop, the unknown resistor is proposed to be measured by noting the current initially and then connecting the unknown resistor across the ammeter. If the ratio of the two current is 2, what is the value of the unknown resistor (rn W ) ?

a. 3000 b. 150 c. 100 d. 50

21.The current I flowing into the branch indicated by an arrow in the circuit shown is equal to


a. 2 Amp b. 0.5 Amp c. 1 Amp d. 0.25 Amp

22. For the circuit shown, the maximum power is delivered to the load resistance RL when the value of Rg is

a. 2 ohms b. zero c. 10 ohms d. infinity

23. A signal generator is available in the laboratory, which is in good condition except for the attenuator dial which has got displaced. In order to calibrate this, a high frequency oscilloscope is available. At a particular setting of the knob an open circuit voltage of 450 mV rms is measured. If the impedance of the generator is 50 ohms, the setting of the attenuator dial is to be adjusted for

a. 6 dBm b. 1 dBm c. 0 dBm d. 10 dBm

24. The relation Loge (X + Loge (1 + X) = 0 also means that

1. X2 + X + 1 = 0

2. X2 + X - 1 = 0

3. X2 + X + e = 0

4. X2 + X – e = 0

25. The Laplace transform of the function f(t) = cos wt is

1. w/(s2 + w2)

2. s2/(s2 - w2)

3. w2/(s2 + w2)

4. s/(s2 + w2)

26. If a = b = c, one value of X which satisfies the equation

=0 is given by

a. x=a b. x=b c. x=c d. x=0

27. An LC oscillator is being analysed. If the LC tank circuit (with quality factor = Q) is isolated from the amplifying device, the impedance at the resonant frequency as measured looking into the amplifier will be

1. Q r [LC]1/2

2. ½ rp r [LC]1/2

3. – Q r[LC]1/2

4. Q r [LC]1/2


28. A battery eliminator is required to be constructed and an assortment of rectifiers, resistors and capacitors is available. However, the step down transformer available has no center tap. The following configurations for the rectifier are feasible. The one giving the lowest ripple will be

1. Full wave rectifier
2. Half wave rectified
3. Bridge rectifier
4. None

29. Chokes used in rectifier filter circuits are wound on a core with a small air gap. This is done in order to

1. Get as high an inductance as possible
2. Prevent saturation of the core
3. Absorb the ripple effectively
4. Prevent loading the transformer

30. An integrated circuit linear regulator is used at the output of a power supply having a ripple of 1 V rms. Assuming that the IC represents a typical design generally available, the output rms ripple to be expected will be

a.. 0.1 V rms b. 0.1 mV c. 100 mV d. 1.0 V rms

best of luck.......

BEL model question papers for electronics engineering

::Question Paper for BHEL Electronics Engineer::


(BHEL) Bharat Heavy Electricals Ltd




please find attachment...

All the best