Education and Career Forum

Sir I am in urgent need of bhel engineer trainee model question paper of electronics major. Thanks in advance for all your help.

here is the model question paper. check it.

BHEL Model question paper(Answers Updated)
1. For ELECTRICAL & ELECTRONICS with answers(bolded words)
2. When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing
through it dissipates 1000 watts then which of the following will have least value in ohms
a.) Resistanceb.) Reactance
c.) Impedance
d.) None
3. Oscillator crystal are made of –
a.) Silicon
b.) Germanium
c.) Quartz
d.) None
4. For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite
c.) Powdered ion
d.) Steel
5. If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a
capacity C and a metallic plate r of area A and of negligible thickness is introduced in the
capacitor at a distance from either of the two plates as shown in the given
figure then the capacity of the capacitor will become –
a.)
b.) C
c.) 2C
d.) 4C
6. A superconductor is a –
a.) A material showing perfect conductivity and Meissner effect below a critical
temperature
b.) A conductor having zero resistance
c.) A perfect conductor with highest di-magnetic susceptibility
d.) A perfect conductor which becomes resistance when the current density through it
exceeds a critical value
7. When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF
capacitor then the self capacitance of the inductor would be –
a) 8.05 pF
b) 10.05pF
c.) 16.01pF
d.) 20.01pF
8. Sparking occur when a load is switched off because the circuit has high –
a.) Inductance
b.) Capacitance
c.) Resistance
d.) None
9. Sparking between contacts can be reduced by inserting a –
a.) Resistance in the line
b.) Capacitor in series with contacts
c.) Capacitor in parallel with contacts
d.) None
10. RF amplifier of an A.M. receiver is normally biased in –
a.) Class ‘A’
b.) Class ‘b’
c.) Class ‘C’
d.) None
11. The value of gate voltage for the operation of enhancement of only N channel MOSFET
has to be –
a.) High positive
b.) High negative
c.) Low positive
d.) Zero
12. The input gate current of a FET is –
a.) a few microamperes
b.) negligibly small
c.) a few milliamperes
d.) a few amperes
13. In the following fig. with R = 30k, the value of current through 2 K resistor is –
a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA
14. A step recovery diode –
a.) has on extremely short recovery time
b.) conducts equally well in both directions
c.) is mainly used as a harmonic generator
d.) is an ideal rectifiers of high frequency signals
15. In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the
value of VCE (Q) should be approximatelya.)
0.1V
b.) 5V
c.) 10V
d) V
16. In a FET the electrode, which corresponds to collector in bipolar transistor, is –
a.) source
b.) drain
c.) gate
d.) none
17. The device which acts like an NPN and a PNP transistor connected base to base and
emitter to collector is –a.) Triacb.) UJT
c.) Diac
d.) SCR
18. A typical optical fibre has –
a.) High refractive index core and low refractive index cladding
b.) Low refractive index core and high refractive index cladding
c.) Both a and b
d.) None
19. In the following figure circuit diagram of an op-amp based is shown. The ratio is
equal to –
a.) 9
b.) 11
c.) 10
d.) 21
20. When a loud speaker is connected across the terminals A and B of the network shown in
the fig. then its impedance to obtain maximum power dissipation in it will be –
a.) 3 – j1
b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
21. In the lattice network, the value of R for the maximum power transfer to the load –
a.) 5
b.) 6.5
c.) 8
d.) 9
22. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (Z0 is the characteristic impedance, √ is the propagation constant and l is the
length of the line-a.) Z0 cot h √lb.) Z0 cot √l
c.) Z0 tan h.√ l
d.) Z0 tan √l
23. The approximate thickness of the radome wall should be –a.) λb.) λ/4
c.) λ/2
d.) λ/8
24. A relatively permanent information is stored in
a. ) ROM
b.) RAM
c.) PROM
d.) Volatile memory
25. The rise time of the RC network shown in the given figure is approximately equal to –
b.) RC
c.) 2RC
d.) 4RC
26. If in the network shown in the fig. initially a steady state is attained by closing the switch
‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will
be – a.) cos50tA
b.) 2A
c.) 2cos100tA
d.) 2sin50tA
27. When the π network of figure – I and T-network of figure – II are equivalent then the
values of R1, R2 and R3 will be respectively – a)
9, 6 and 6
b.) 6, 6 and 9
c.) 9, 6 and 9
d.) 6, 9 and 6
28. When the impedance matrices of a two port networks are given by and ,
then if these two networks are connected in series then the impedance matrix of the
resulting two-port network will be –
d.) indeterminate
29. Joule/coulomb is the unit of - a.) Electric field potential b.) Potential
c .) Charge
d.) None of the above
30. The electric field line and equipotential linesa.)
Are parallel to each other
b.)Are one and same
c.) Cut each other orthogonally
d.)Can be inclined to each other at any angle
31. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (When Z0 is the characteristic impendence γ is the propagation constant and L is
the length of the line
32. When two equal positive point charges are placed along X- axis at X1 and –X1
respectively then the electric field vector at a point P on the positive Y-axis will be
directeda.)
In the +x direction
b.) In the –x direction
c. ) In the +y direction
d.) In the –y direction
33. The directions of and in TEM mode transmission line with respect to the direction of
propagation area.)
Both and are transverse to the direction of propagation
b.) is and are transverse and h has a component in the direction of propagation
c.) is entirely transverse and has a component in the direction of propagation
d. ) is entirely transverse and has a component in the direction of propagation
34. The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will bea.)
TM01
b.)TE10
c.) TM112
d.)TE11
35. When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all
directions then at a distance d sufficiently far from the source in plane the electric field E
should be related to p and d as –
36. . When a dipole antenna was radiating with some excitation in free space radiating a
certain amount of the power v if then this antenna is immersed in a lake where water is
non-dissipative but has a dielectric constant of 81, then the radiated power with the same
excitation will be
a.) Decrease to finite non-zero value
b.)Remain the same
c. )Increase
d.)Decrease to zero
37. When a (75 – j40) load is connected to a coaxial line of Z0 = 75  at 6MHz then the
load matching on the line can be accomplished by connectinga.)
A short – circuited stub at the load
b.)An inductance at the load
c. )A short circuited stub at a specific distance from the load
d.)none of the above
38. As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more
accurate
c.) equally accurate
d.) none.
39. When a signal of 10 mV at 75 MHz is to be measured then which of the following
instruments can be used –a.) VTVMb.) Cathode ray oscilloscope
c.) Moving iron voltmeter
d.) Digital multimeter
40. Which of the following statement is true about two wattmeter method for power
measurement in three phase current ?a.) power can be measured using two wattmeter
method only for star connected three phase circuits.b.) when two meter show indentical
readings, in the power factor is 0.5.
c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the
power factor is zero –
41. When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap
of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.)
11.1b.) 44.2
c.) 52.3
d.) 66.3
42. The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as
frequency increases
c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
43. When a generator of internal impedance and operating at 1GHz feeds a load via
a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed
line is –a.) 0.5b.) 1.5
c.) 2.5
d.) 1.75
44. The coding system typically used in digital telemetry is –a.) PPM (pulse position
modulation)b.) PAM (pulse amplitude modulation)
c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
45. Radiation pyrometers are used for the measurement of temperature in the range of –
a.) -2000C to 5000C
b.) 00C to 5000C
c.) 5000C to 12000C
d.) 12000C to 25000C
46. In the given figure band structure is shown. It is of –
a.) Gallium Avesenide (GaAs)
b.) Silicon (Si)
c.) Copper (Cu)
d.) Germanium (Ge)
47. When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n
junction is –
a.) 1
b.) 2
c.) 3
d.) 4
48. The circuit symbol for a GTO is
a. b.
c. d.
49. In the given fig. mark out the type of Cyclo converters
a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device
In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the
switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.
a.) 400 A, 15.707 mS
50. b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS
51. 50. In the given circuit the maximum current in the main SCR M can bea.)
200 A
b.) 170.7 A
c.) 141.4 A
d.) 70.7 A
52. The transfer function of an amplifier is given by The
high 3-db frequency of the amplifier will approximately
a.) 5850 KHZ
b.)585 KHZ
c.) 5850 HZ
d.)585HZ
53. In comparison to full wave rectifier with two diodes the four divide bridge rectifier has
the dominant advantage of -
a). Higher current carrying
b.)Lower ripple factor
c.) Higher efficiency
d.)Lower peak increase voltage require
54. Power output increase in a class-c amplifiera.)
If the conduction angle decrease
b).If the conduction angle increase
c.) Are not governed by the conduction angle
d.)None of the above
55. A transistor with hie = 1.5 k and hfe = 75 is used in an emitter follower circuit where R1
and R2 are used for normal biasing . Approximate value of it’s current amplification isa.)
75b.)76
c.)75/76
d.)-75
56. Amplifier of class B has high theoretical efficiency of 78.5 percent becausea.)
It is biased almost to saturation
b.)Its quiescent current is low
c.)It’s output is an exact replica of it’s input
d.)It is biased well below cut off
57. The coupling that produces minimum interference with frequency response isa.)
Direct coupling
b.)Impedance coupling
c.) R C coupling
d.)Transformer coupling
58. In the circuit shown in the given figure Rf provides
a.) Current series feedback
b.)Current shunt feedback
c.) Voltage series feedback
d.)Voltage shunt feedback
59. Mark the correct relation for the junction transistor
60. Data in the serial form can be converted into parallel form by using –a.) PISO shift
registerb.) SOIP shift register
c.) SIPO shift register
d.) POIS shift register
61. PROMs are used to store-a.) bulk informationb.) information to be accessed rarely
c.) sequence information
d.) relatively permanent information
62. The horizontal axis in a 3 bit unipolar D/A converter represents-a.) Output bit
combinationb.) analog output voltage
c.) input bit combination
d.) none of the above
63. ‘Not allowed’ condition in NAND gate SR flip flop is –a.) s = 0, R = 0b.) s = 1, R = 1
c.) s = 0, R = 1
d.) s = 1, R = 0
64. Name the fastest logic family-a) TTLb.) RTL
c.) DCTL
d.) ECL
65. Equation corresponding to De Morgan’s theorem in Boolean Algebra is – a.) (A+B)
(A+B) = AA + AB + BA + BB
c.) A + AB = A
d.) None of the above
66. In the given fig find radix of the system –
a.) 2
b.) 4
c.) 6
d.) 8
67. Modems are used for data transmission telephone lines to –a.) increase the transmission
capacityb) improve noice performance
c.) incorporate error control coding
d.) eliminate dc component in the transmitted signal
68. The figure of a control system is shown. The maximum value of gain K for which the
system is stable is- a.)
b.) 3
c.) 4
d.) 5
69. Identify the example of open-loop system-a.) A windscreen wiperb.) Aqualung
c.) Respiratory system of an animal
d.) A system for controlling Anti-rocket missiles.
70. Consider the following expressions indicating the step or impulse response of an initially
relaxed control system-1. (5 – 4e-2+) u(t)2. (e-2t +5) (u(t))
3 .ς(t) + 8e-2t u(t)
4 . ς(t) + 4e-2t 4(t)
Those which correspond to the step and impulse response of the same system includea.)
1&3
b.) 1&4
c.) 2&4
d.) 1&4
71. A system is described by
To test its stability by Lyapunov’s method the following V functions are considered.
Mark the most suitable V-function in this casea.)
Only V1
b.) Only V2
c.) Both V1 and V2
d.) Neither V1 nor v2
72. Identity the polar plot of a typical type zero system with open loop transfer function
73. The scattering matrix of a magic –tee shown in the given figure is-
74. Which is the following relate to rational transfer function of a system-1. Ratio of Fourier
transform of output to input with zero initial conditions.2. Ratio of Laplace transform of
output to input with zero initial conditions.
3. Laplace transform of system impulse response.
4. Laplace transform of system unit step response select the correct answer using the
codes given below.
Codes
a.) 1 and 4
b.) 2 and 3
c.) 1 and 3
d.) 2 and 4
75. For the signal g (t) – 10 cos (50 pt) cos2 (150at)The Nyquist sampling state in t seconds
isa.) 150 samples per second
b.) 200 samples per second
c.) 300 samples per second
d.) 350 samples per second
76. In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must
lie between – MHz.a.) 34 and 106b.) 52. And 88
c.) 106 and 142
d.) 34 and 142
77. Radar used to eliminate clutter in navigational application is –a.) Pulse radarb.) Tracking
radar
c.) MTI radar
d.) Mono pulse radar
78. The 1.55 mm windows is not yet in use with fiber optic systems because –a.) The
attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mm
c.) Suitable laser devices have not yet been developed
d.) It does not lend itself to wavelength multiplexing
79. Pre-emphasis in FM systems involves-a.) Compression of the modulating signalb.)
Expansion of the modulating signal
c.) Amplification of lower frequency components of the modulating signal.
d.) Amplification of higher frequency components of the modulating signal.
80. In a terrestrial microwave system transmission of signals is achieved through-a.)
reflection from the ionosphereb.) line of sight mode
c) reflection from the ground
d.) diffraction from the stratosphere.
81. Casse grain feed is used with a parabolic reflector toa.) increase the gain of the systemb).
increase the bandwidth of the system
c.) reduce the size of the main reflector
d.) allow the feed to be placed at a convenient point.
82. In most microwave communication link rain drop attenuation is caused due to-a.)
scattering of microwaves by water drops of specific size.b) scattering of microwaves by a
collection of droplets acing as a single body.
c.) absorption of microwaves by water and consequent heating of the liquid
d.) absorption of the microwaves by water vapor in the atmosphere.
83. Circuit in the given figure represents. – a.) an astable
multivibrator
b.) A monostable multivibrator
c.) Voltage controlled oscillator
d.) Ramp generator
84. . . D = r is-a.) Maxwell’s 1st equationb.) Maxwell’s II equation
c.) Maxwell’s III equation
d.) Maxwell’s IV equation
85. In a rectangular wave-guide which TM mode exists-a.) TM00b.) TM01
c.) Tm10
d.) TM11
86. In directional coupler a portion of power two velliry fram port 1) to port 2) is coupled
to.a). port 4b). port 3
c.) port 2.
d.) port 3 & 4.
87. For high power i.e. 10 w to 50 kw measurement –
a.) Barometer are used
b.) Thermisters are used
c.) Calorimetric technique
d.) Calorimetric watt meter technique used
88. The difference between TWT & klystron is –
a.) In TWT electrons are in contact with RF field for long time & in klystron for
short time
b.) In klystron electrons are in contact with RF field for long time & in TWT for short
time
c.) In klystron there is no contact in RF field & electrons while in TWT there is contact
d.) In TWT phase is no contact is RF field & electrons while in klystron there is contact
89. Which one is most suitable for transmission through wave guidea.)
Hown antennas
b.) Bioconical antennas
c.) helical antenna
d. )Discone
90. The skip distance of microwave is given by –
a.)
b. )
c.)
d.)
91. How many general purpose registers 8085mpa.)
4
b.) 6
c.) 8
c.) 10
92. 8085 mP has no. of addressing modesa.)
2
b.) 3
c.) 4
d.) 5
93. What will be status of z and c y flag after execution of SUB A instruction
a.) z = 0, cy = 0
b.) z = 0, cy = 1
c.) z = 1, cy = 0
d.) z = 1, cy = 1
94. Microprocessor accept interrupt only if.
a.) interrupt flip flop disabled.
b.) when INTA signal is low.
c. ) interrupt flip flop enabled.
d.) none of above.
95. Microprogramming is a technique
a.) for programming the microprocessor
b.) for writing small programs efficiently
c.) for programming the control steps of computer
d.) for programming o/p / i/p
96. High level programs like C are converted into machine language with the help ofa.)
interpreterb.) compiler
c.) operating
d.) system
97. (10110011)2 = (?)8a.) 253b.) 263
c.) 273
d.) 283
98. A Not gate at the output of AND gate converts AND gate into-a.) NANDb.) NOR
c.) AND
d.) NOPE.
99. The O/P of a logic gate is the gate must be-a.) ANDb.) OR
c.) NAND
d.) X-OR
100. A symbol of JK flip flop is-
101. A demultiplener-a.) has multiple i/p and single o/pb.) has multiple i/p and
multiple o/p
c.) has multiple i/p and multiple o/p
d.) has single i/p and single o/p
102. . Which of the following best describes the authour`s attitude toward fairy tales
?a.) fascinationb.) open approval.
c.) Indulgent tolerance.
d.) Scornful.
103. What type of sentence is this ?Hurray! We won the matcha.) Exclamatory
b.) assertive
c.) Negative
d.) Affirmative
104. Before which of the following word will you put ‘a’a.) hourb.) M. A.
c.) Umbrella
d.) Man
105. The noun form of ‘fresh’ is –a.) freshlyb.) freshen
c.) fresheners
d.) fresh itself
106. The word ‘clang’ is an example of –a.) Simileb.) inversion
c.) onomatopoeia
d.) irony
107. The Forbes magazine acclaimed Azim Premji as richest India’s is the chairman
of-a.) Pentafour softwareb) Infosys
c.) IBM
d.) Wipro
108. Bharat Ratna award for the year 2001 goes to-a.) Lata Mangeshkar and Zakeer
Hussainb.) Zakeer Hussain and Bismillah Khan
c.) Bismillah Khan and Lata Mangeshkar
d.) Lata Mangeshkar and Ustad Amzad Ali Khan
109. Mr. George W-Bush takes over as —— President of the united states of America
succeeding Mr. Bill Clinton-a.) 42nd
b.) 43rd
c.) 40th
d.) 45th
110. New Chief Minister of Pondicherry is-a.) T. Venkat Naidub.) K. Hari Harh
c.) N. Rengaswany
d.) M. Mudliar
111. No court has the jurisdiction to interfere with the election process once set in
motion by the Election commission. This is enshrined in Article-a.) 311b.) 329
c.) 356
d.) 365
112. Ostrich is a-a.) Running birdb.) Flying bird
c) Swimming bird
d.) Migratory bird
113. The main atmospheric gas responsible for green house is-a.) Oxygenb.) Nitrogen
c.) Ozone
d.) Carbon-dioxide
114. Which of the following is not a Kharif Crop-a.) Riceb.) groundnut
c.) Sugarcane
d.) gram
115. The function of World Bank is to-a.) Help in reconstruction and development
of world economyb.) Facilitate poor countries to trade on concessional rates
c.) Promote growth of international trade and equilibrium in balance of payments
d.) Ease trade barriers and establish rule of fair trade
116. Speed of sound is maximum in-a. )Waterb.) Air
c.) Steel
d.) Vacuum
117. “Long years ago we made a trust with destiny.” Whose words are these-a.)
Subhash Chandra Boseb.) Jawaharlal Nehru
c.) Lajpat Rai
d.) Bhagat Singh
118. Durand cup is associated with-a.) Hockeyb.) Tennis
c.) Football
d.) Badminton
119. Rabindranath Tagore was awarded the Nobel Prize in literature in the year.a.)
1908b.) 1910
c.) 1913
d.) 1914
120. India successfully conducted its first underground nuclear experiment at Pokhran
in Rajas than on-a.) May 18, 1975b.) May 20, 1974
c) May 17, 1974
d.) May 17, 1974
121. An emergency loan of $ 500 million to help reconstruct infrastructure in earth
quake devastated Gujarat approved by-a.) Asian development Bankb.) World Bank
c.) Swiss Bank
d.) Reserve Bank of India

where is answer of the above question paper?

good morning , i have submitted bhel online application with OBC cast, but here due to internet problem i am not
getting my cast certificate at now .so my question is can i send my document without cast certificate or you may consider it as GEN..

please tell me the above question answers as all letters are same neither bold nor easily identified

hai friends,
this is dinesh. the answer for above questions are in the following link
http://senthil4u.wordpress.com/2009/09/08/bhel-modern-question-paper/

please tell basic question for bhel.......for superviser trainee

electronics engineering bhel question paper

hello friend

see, bhel exam syllabus for engineer trainee syllabus is equivalent to gate syllabus.so it will be better to take gate syllabus as a bhel exam syllabus for engineer trainee.

you can get Gate syllabus & model question in the given below sites

1.www.gateforum.com.

2.www.onestopgate.com.

all the best...............

hello sir,,,,here madhu,,last month sep 20th i send my application form through courier for engineer trainee,,but in bhel link when i check my status of my application form , it was displayed that no such application form,,,so i dono wether u received my application form or not sir? my aknowledgement number is 1049903...pls check and inform sir?

Pls send me the ques paper 4 Bhel engineer trainee (Electrical) ASAP at [email protected]

Originally Posted by Unregistered

good morning , i have submitted bhel online application with OBC cast, but here due to internet problem i am not
getting my cast certificate at now .so my question is can i send my document without cast certificate or you may consider it as GEN..

as you are unable to submit OBC caste certificate so you will be considered as general candidate. so there will no reservation for you and also you will not get the facility for being OBC.

Originally Posted by JAMESS

as you are unable to submit OBC caste certificate so you will be considered as general candidate. so there will no reservation for you and also you will not get the facility for being OBC.

I have not sent this thread 2 u.. i Asked about the BHEL engineer trainee sample question papers 4 electrical

thanks for make us to get idea about questions

i want the model question for electrical discipline in ET bhel exam.

please send BHEL engineer trainee model question paper @ [email protected]

hello sir.. there is no response for my ques yet.. u r my last hope.. wen will the personal interview be conducted for the selected students in written test... is it on the same day of written test? sir please give me reply as early as possible.. thank you sir..

Originally Posted by elakkiya505

Sir I am in urgent need of bhel engineer trainee model question paper of electronics major. Thanks in advance for all your help.

BHEL Model question paper(Answers Updated)
1. For ELECTRICAL & ELECTRONICS with answers(bolded words)
2. When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing
through it dissipates 1000 watts then which of the following will have least value in ohms
a.) Resistanceb.) Reactance
c.) Impedance
d.) None
3. Oscillator crystal are made of –
a.) Silicon
b.) Germanium
c.) Quartz
d.) None
4. For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite
c.) Powdered ion
d.) Steel
5. If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a
capacity C and a metallic plate r of area A and of negligible thickness is introduced in the
capacitor at a distance from either of the two plates as shown in the given
figure then the capacity of the capacitor will become –
a.)
b.) C
c.) 2C
d.) 4C
6. A superconductor is a –
a.) A material showing perfect conductivity and Meissner effect below a critical
temperature
b.) A conductor having zero resistance
c.) A perfect conductor with highest di-magnetic susceptibility
d.) A perfect conductor which becomes resistance when the current density through it
exceeds a critical value
7. When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF
capacitor then the self capacitance of the inductor would be –
a) 8.05 pF
b) 10.05pF
c.) 16.01pF
d.) 20.01pF
8. Sparking occur when a load is switched off because the circuit has high –
a.) Inductance
b.) Capacitance
c.) Resistance
d.) None
9. Sparking between contacts can be reduced by inserting a –
a.) Resistance in the line
b.) Capacitor in series with contacts
c.) Capacitor in parallel with contacts
d.) None
10. RF amplifier of an A.M. receiver is normally biased in –
a.) Class ‘A’
b.) Class ‘b’
c.) Class ‘C’
d.) None
11. The value of gate voltage for the operation of enhancement of only N channel MOSFET
has to be –
a.) High positive
b.) High negative
c.) Low positive
d.) Zero
12. The input gate current of a FET is –
a.) a few microamperes
b.) negligibly small
c.) a few milliamperes
d.) a few amperes
13. In the following fig. with R = 30k, the value of current through 2 K resistor is –
a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA
14. A step recovery diode –
a.) has on extremely short recovery time
b.) conducts equally well in both directions
c.) is mainly used as a harmonic generator
d.) is an ideal rectifiers of high frequency signals
15. In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the
value of VCE (Q) should be approximatelya.)
0.1V
b.) 5V
c.) 10V
d) V
16. In a FET the electrode, which corresponds to collector in bipolar transistor, is –
a.) source
b.) drain
c.) gate
d.) none
17. The device which acts like an NPN and a PNP transistor connected base to base and
emitter to collector is –a.) Triacb.) UJT
c.) Diac
d.) SCR
18. A typical optical fibre has –
a.) High refractive index core and low refractive index cladding
b.) Low refractive index core and high refractive index cladding
c.) Both a and b
d.) None
19. In the following figure circuit diagram of an op-amp based is shown. The ratio is
equal to –
a.) 9
b.) 11
c.) 10
d.) 21
20. When a loud speaker is connected across the terminals A and B of the network shown in
the fig. then its impedance to obtain maximum power dissipation in it will be –
a.) 3 – j1
b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
21. In the lattice network, the value of R for the maximum power transfer to the load –
a.) 5
b.) 6.5
c.) 8
d.) 9
22. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (Z0 is the characteristic impedance, √ is the propagation constant and l is the
length of the line-a.) Z0 cot h √lb.) Z0 cot √l
c.) Z0 tan h.√ l
d.) Z0 tan √l
23. The approximate thickness of the radome wall should be –a.) λb.) λ/4
c.) λ/2
d.) λ/8
24. A relatively permanent information is stored in
a. ) ROM
b.) RAM
c.) PROM
d.) Volatile memory
25. The rise time of the RC network shown in the given figure is approximately equal to –
b.) RC
c.) 2RC
d.) 4RC
26. If in the network shown in the fig. initially a steady state is attained by closing the switch
‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will
be – a.) cos50tA
b.) 2A
c.) 2cos100tA
d.) 2sin50tA
27. When the π network of figure – I and T-network of figure – II are equivalent then the
values of R1, R2 and R3 will be respectively – a)
9, 6 and 6
b.) 6, 6 and 9
c.) 9, 6 and 9
d.) 6, 9 and 6
28. When the impedance matrices of a two port networks are given by and ,
then if these two networks are connected in series then the impedance matrix of the
resulting two-port network will be –
d.) indeterminate
29. Joule/coulomb is the unit of - a.) Electric field potential b.) Potential
c .) Charge
d.) None of the above
30. The electric field line and equipotential linesa.)
Are parallel to each other
b.)Are one and same
c.) Cut each other orthogonally
d.)Can be inclined to each other at any angle
31. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (When Z0 is the characteristic impendence γ is the propagation constant and L is
the length of the line
32. When two equal positive point charges are placed along X- axis at X1 and –X1
respectively then the electric field vector at a point P on the positive Y-axis will be
directeda.)
In the +x direction
b.) In the –x direction
c. ) In the +y direction
d.) In the –y direction
33. The directions of and in TEM mode transmission line with respect to the direction of
propagation area.)
Both and are transverse to the direction of propagation
b.) is and are transverse and h has a component in the direction of propagation
c.) is entirely transverse and has a component in the direction of propagation
d. ) is entirely transverse and has a component in the direction of propagation
34. The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will bea.)
TM01
b.)TE10
c.) TM112
d.)TE11
35. When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all
directions then at a distance d sufficiently far from the source in plane the electric field E
should be related to p and d as –
36. . When a dipole antenna was radiating with some excitation in free space radiating a
certain amount of the power v if then this antenna is immersed in a lake where water is
non-dissipative but has a dielectric constant of 81, then the radiated power with the same
excitation will be
a.) Decrease to finite non-zero value
b.)Remain the same
c. )Increase
d.)Decrease to zero
37. When a (75 – j40) load is connected to a coaxial line of Z0 = 75  at 6MHz then the
load matching on the line can be accomplished by connectinga.)
A short – circuited stub at the load
b.)An inductance at the load
c. )A short circuited stub at a specific distance from the load
d.)none of the above
38. As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more
accurate
c.) equally accurate
d.) none.
39. When a signal of 10 mV at 75 MHz is to be measured then which of the following
instruments can be used –a.) VTVMb.) Cathode ray oscilloscope
c.) Moving iron voltmeter
d.) Digital multimeter
40. Which of the following statement is true about two wattmeter method for power
measurement in three phase current ?a.) power can be measured using two wattmeter
method only for star connected three phase circuits.b.) when two meter show indentical
readings, in the power factor is 0.5.
c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the
power factor is zero –
41. When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap
of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.)
11.1b.) 44.2
c.) 52.3
d.) 66.3
42. The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as
frequency increases
c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
43. When a generator of internal impedance and operating at 1GHz feeds a load via
a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed
line is –a.) 0.5b.) 1.5
c.) 2.5
d.) 1.75
44. The coding system typically used in digital telemetry is –a.) PPM (pulse position
modulation)b.) PAM (pulse amplitude modulation)
c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
45. Radiation pyrometers are used for the measurement of temperature in the range of –
a.) -2000C to 5000C
b.) 00C to 5000C
c.) 5000C to 12000C
d.) 12000C to 25000C
46. In the given figure band structure is shown. It is of –
a.) Gallium Avesenide (GaAs)
b.) Silicon (Si)
c.) Copper (Cu)
d.) Germanium (Ge)
47. When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n
junction is –
a.) 1
b.) 2
c.) 3
d.) 4
48. The circuit symbol for a GTO is
a. b.
c. d.
49. In the given fig. mark out the type of Cyclo converters
a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device
In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the
switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.
a.) 400 A, 15.707 mS
50. b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS
51. 50. In the given circuit the maximum current in the main SCR M can bea.)
200 A
b.) 170.7 A
c.) 141.4 A
d.) 70.7 A
52. The transfer function of an amplifier is given by The
high 3-db frequency of the amplifier will approximately
a.) 5850 KHZ
b.)585 KHZ
c.) 5850 HZ
d.)585HZ
53. In comparison to full wave rectifier with two diodes the four divide bridge rectifier has
the dominant advantage of -
a). Higher current carrying
b.)Lower ripple factor
c.) Higher efficiency
d.)Lower peak increase voltage require
54. Power output increase in a class-c amplifiera.)
If the conduction angle decrease
b).If the conduction angle increase
c.) Are not governed by the conduction angle
d.)None of the above
55. A transistor with hie = 1.5 k and hfe = 75 is used in an emitter follower circuit where R1
and R2 are used for normal biasing . Approximate value of it’s current amplification isa.)
75b.)76
c.)75/76
d.)-75
56. Amplifier of class B has high theoretical efficiency of 78.5 percent becausea.)
It is biased almost to saturation
b.)Its quiescent current is low
c.)It’s output is an exact replica of it’s input
d.)It is biased well below cut off
57. The coupling that produces minimum interference with frequency response isa.)
Direct coupling
b.)Impedance coupling
c.) R C coupling
d.)Transformer coupling
58. In the circuit shown in the given figure Rf provides
a.) Current series feedback
b.)Current shunt feedback
c.) Voltage series feedback
d.)Voltage shunt feedback
59. Mark the correct relation for the junction transistor
60. Data in the serial form can be converted into parallel form by using –a.) PISO shift
registerb.) SOIP shift register
c.) SIPO shift register
d.) POIS shift register
61. PROMs are used to store-a.) bulk informationb.) information to be accessed rarely
c.) sequence information
d.) relatively permanent information
62. The horizontal axis in a 3 bit unipolar D/A converter represents-a.) Output bit
combinationb.) analog output voltage
c.) input bit combination
d.) none of the above
63. ‘Not allowed’ condition in NAND gate SR flip flop is –a.) s = 0, R = 0b.) s = 1, R = 1
c.) s = 0, R = 1
d.) s = 1, R = 0
64. Name the fastest logic family-a) TTLb.) RTL
c.) DCTL
d.) ECL
65. Equation corresponding to De Morgan’s theorem in Boolean Algebra is – a.) (A+B)
(A+B) = AA + AB + BA + BB
c.) A + AB = A
d.) None of the above
66. In the given fig find radix of the system –
a.) 2
b.) 4
c.) 6
d.) 8
67. Modems are used for data transmission telephone lines to –a.) increase the transmission
capacityb) improve noice performance
c.) incorporate error control coding
d.) eliminate dc component in the transmitted signal
68. The figure of a control system is shown. The maximum value of gain K for which the
system is stable is- a.)
b.) 3
c.) 4
d.) 5
69. Identify the example of open-loop system-a.) A windscreen wiperb.) Aqualung
c.) Respiratory system of an animal
d.) A system for controlling Anti-rocket missiles.
70. Consider the following expressions indicating the step or impulse response of an initially
relaxed control system-1. (5 – 4e-2+) u(t)2. (e-2t +5) (u(t))
3 .ς(t) + 8e-2t u(t)
4 . ς(t) + 4e-2t 4(t)
Those which correspond to the step and impulse response of the same system includea.)
1&3
b.) 1&4
c.) 2&4
d.) 1&4
71. A system is described by
To test its stability by Lyapunov’s method the following V functions are considered.
Mark the most suitable V-function in this casea.)
Only V1
b.) Only V2
c.) Both V1 and V2
d.) Neither V1 nor v2
72. Identity the polar plot of a typical type zero system with open loop transfer function
73. The scattering matrix of a magic –tee shown in the given figure is-
74. Which is the following relate to rational transfer function of a system-1. Ratio of Fourier
transform of output to input with zero initial conditions.2. Ratio of Laplace transform of
output to input with zero initial conditions.
3. Laplace transform of system impulse response.
4. Laplace transform of system unit step response select the correct answer using the
codes given below.
Codes
a.) 1 and 4
b.) 2 and 3
c.) 1 and 3
d.) 2 and 4
75. For the signal g (t) – 10 cos (50 pt) cos2 (150at)The Nyquist sampling state in t seconds
isa.) 150 samples per second
b.) 200 samples per second
c.) 300 samples per second
d.) 350 samples per second
76. In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must
lie between – MHz.a.) 34 and 106b.) 52. And 88
c.) 106 and 142
d.) 34 and 142
77. Radar used to eliminate clutter in navigational application is –a.) Pulse radarb.) Tracking
radar
c.) MTI radar
d.) Mono pulse radar
78. The 1.55 mm windows is not yet in use with fiber optic systems because –a.) The
attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mm
c.) Suitable laser devices have not yet been developed
d.) It does not lend itself to wavelength multiplexing
79. Pre-emphasis in FM systems involves-a.) Compression of the modulating signalb.)
Expansion of the modulating signal
c.) Amplification of lower frequency components of the modulating signal.
d.) Amplification of higher frequency components of the modulating signal.
80. In a terrestrial microwave system transmission of signals is achieved through-a.)
reflection from the ionosphereb.) line of sight mode
c) reflection from the ground
d.) diffraction from the stratosphere.
81. Casse grain feed is used with a parabolic reflector toa.) increase the gain of the systemb).
increase the bandwidth of the system
c.) reduce the size of the main reflector
d.) allow the feed to be placed at a convenient point.
82. In most microwave communication link rain drop attenuation is caused due to-a.)
scattering of microwaves by water drops of specific size.b) scattering of microwaves by a
collection of droplets acing as a single body.
c.) absorption of microwaves by water and consequent heating of the liquid
d.) absorption of the microwaves by water vapor in the atmosphere.
83. Circuit in the given figure represents. – a.) an astable
multivibrator
b.) A monostable multivibrator
c.) Voltage controlled oscillator
d.) Ramp generator
84. . . D = r is-a.) Maxwell’s 1st equationb.) Maxwell’s II equation
c.) Maxwell’s III equation
d.) Maxwell’s IV equation
85. In a rectangular wave-guide which TM mode exists-a.) TM00b.) TM01
c.) Tm10
d.) TM11
86. In directional coupler a portion of power two velliry fram port 1) to port 2) is coupled
to.a). port 4b). port 3
c.) port 2.
d.) port 3 & 4.
87. For high power i.e. 10 w to 50 kw measurement –
a.) Barometer are used
b.) Thermisters are used
c.) Calorimetric technique
d.) Calorimetric watt meter technique used
88. The difference between TWT & klystron is –
a.) In TWT electrons are in contact with RF field for long time & in klystron for
short time
b.) In klystron electrons are in contact with RF field for long time & in TWT for short
time
c.) In klystron there is no contact in RF field & electrons while in TWT there is contact
d.) In TWT phase is no contact is RF field & electrons while in klystron there is contact
89. Which one is most suitable for transmission through wave guidea.)
Hown antennas
b.) Bioconical antennas
c.) helical antenna
d. )Discone
90. The skip distance of microwave is given by –
a.)
b. )
c.)
d.)
91. How many general purpose registers 8085mpa.)
4
b.) 6
c.) 8
c.) 10
92. 8085 mP has no. of addressing modesa.)
2
b.) 3
c.) 4
d.) 5
93. What will be status of z and c y flag after execution of SUB A instruction
a.) z = 0, cy = 0
b.) z = 0, cy = 1
c.) z = 1, cy = 0
d.) z = 1, cy = 1
94. Microprocessor accept interrupt only if.
a.) interrupt flip flop disabled.
b.) when INTA signal is low.
c. ) interrupt flip flop enabled.
d.) none of above.
95. Microprogramming is a technique
a.) for programming the microprocessor
b.) for writing small programs efficiently
c.) for programming the control steps of computer
d.) for programming o/p / i/p
96. High level programs like C are converted into machine language with the help ofa.)
interpreterb.) compiler
c.) operating
d.) system
97. (10110011)2 = (?)8a.) 253b.) 263
c.) 273
d.) 283
98. A Not gate at the output of AND gate converts AND gate into-a.) NANDb.) NOR
c.) AND
d.) NOPE.
99. The O/P of a logic gate is the gate must be-a.) ANDb.) OR
c.) NAND
d.) X-OR
100. A symbol of JK flip flop is-
101. A demultiplener-a.) has multiple i/p and single o/pb.) has multiple i/p and
multiple o/p
c.) has multiple i/p and multiple o/p
d.) has single i/p and single o/p
102. . Which of the following best describes the authour`s attitude toward fairy tales
?a.) fascinationb.) open approval.
c.) Indulgent tolerance.
d.) Scornful.
103. What type of sentence is this ?Hurray! We won the matcha.) Exclamatory
b.) assertive
c.) Negative
d.) Affirmative
104. Before which of the following word will you put ‘a’a.) hourb.) M. A.
c.) Umbrella
d.) Man
105. The noun form of ‘fresh’ is –a.) freshlyb.) freshen
c.) fresheners
d.) fresh itself
106. The word ‘clang’ is an example of –a.) Simileb.) inversion
c.) onomatopoeia
d.) irony
107. The Forbes magazine acclaimed Azim Premji as richest India’s is the chairman
of-a.) Pentafour softwareb) Infosys
c.) IBM
d.) Wipro
108. Bharat Ratna award for the year 2001 goes to-a.) Lata Mangeshkar and Zakeer
Hussainb.) Zakeer Hussain and Bismillah Khan
c.) Bismillah Khan and Lata Mangeshkar
d.) Lata Mangeshkar and Ustad Amzad Ali Khan
109. Mr. George W-Bush takes over as —— President of the united states of America
succeeding Mr. Bill Clinton-a.) 42nd
b.) 43rd
c.) 40th
d.) 45th
110. New Chief Minister of Pondicherry is-a.) T. Venkat Naidub.) K. Hari Harh
c.) N. Rengaswany
d.) M. Mudliar
111. No court has the jurisdiction to interfere with the election process once set in
motion by the Election commission. This is enshrined in Article-a.) 311b.) 329
c.) 356
d.) 365
112. Ostrich is a-a.) Running birdb.) Flying bird
c) Swimming bird
d.) Migratory bird
113. The main atmospheric gas responsible for green house is-a.) Oxygenb.) Nitrogen
c.) Ozone
d.) Carbon-dioxide
114. Which of the following is not a Kharif Crop-a.) Riceb.) groundnut
c.) Sugarcane
d.) gram
115. The function of World Bank is to-a.) Help in reconstruction and development
of world economyb.) Facilitate poor countries to trade on concessional rates
c.) Promote growth of international trade and equilibrium in balance of payments
d.) Ease trade barriers and establish rule of fair trade
116. Speed of sound is maximum in-a. )Waterb.) Air
c.) Steel
d.) Vacuum
117. “Long years ago we made a trust with destiny.” Whose words are these-a.)
Subhash Chandra Boseb.) Jawaharlal Nehru
c.) Lajpat Rai
d.) Bhagat Singh
118. Durand cup is associated with-a.) Hockeyb.) Tennis
c.) Football
d.) Badminton
119. Rabindranath Tagore was awarded the Nobel Prize in literature in the year.a.)
1908b.) 1910
c.) 1913
d.) 1914
120. India successfully conducted its first underground nuclear experiment at Pokhran
in Rajas than on-a.) May 18, 1975b.) May 20, 1974
c) May 17, 1974
d.) May 17, 1974
121. An emergency loan of $ 500 million to help reconstruct infrastructure in earth
quake devastated Gujarat approved by-a.) Asian development Bankb.) World Bank
c.) Swiss Bank
d.) Reserve Bank of India


#3 15th September 2010, 04:26 PM

Originally Posted by elakkiya505

Sir I am in urgent need of bhel engineer trainee model question paper of electronics major. Thanks in advance for all your help.

here is the model question paper. check it.

BHEL Model question paper(Answers Updated)
1. For ELECTRICAL & ELECTRONICS with answers(bolded words)
2. When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing
through it dissipates 1000 watts then which of the following will have least value in ohms
a.) Resistanceb.) Reactance
c.) Impedance
d.) None
3. Oscillator crystal are made of –
a.) Silicon
b.) Germanium
c.) Quartz
d.) None
4. For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite
c.) Powdered ion
d.) Steel
5. If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a
capacity C and a metallic plate r of area A and of negligible thickness is introduced in the
capacitor at a distance from either of the two plates as shown in the given
figure then the capacity of the capacitor will become –
a.)
b.) C
c.) 2C
d.) 4C
6. A superconductor is a –
a.) A material showing perfect conductivity and Meissner effect below a critical
temperature
b.) A conductor having zero resistance
c.) A perfect conductor with highest di-magnetic susceptibility
d.) A perfect conductor which becomes resistance when the current density through it
exceeds a critical value
7. When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF
capacitor then the self capacitance of the inductor would be –
a) 8.05 pF
b) 10.05pF
c.) 16.01pF
d.) 20.01pF
8. Sparking occur when a load is switched off because the circuit has high –
a.) Inductance
b.) Capacitance
c.) Resistance
d.) None
9. Sparking between contacts can be reduced by inserting a –
a.) Resistance in the line
b.) Capacitor in series with contacts
c.) Capacitor in parallel with contacts
d.) None
10. RF amplifier of an A.M. receiver is normally biased in –
a.) Class ‘A’
b.) Class ‘b’
c.) Class ‘C’
d.) None
11. The value of gate voltage for the operation of enhancement of only N channel MOSFET
has to be –
a.) High positive
b.) High negative
c.) Low positive
d.) Zero
12. The input gate current of a FET is –
a.) a few microamperes
b.) negligibly small
c.) a few milliamperes
d.) a few amperes
13. In the following fig. with R = 30k, the value of current through 2 K resistor is –
a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA
14. A step recovery diode –
a.) has on extremely short recovery time
b.) conducts equally well in both directions
c.) is mainly used as a harmonic generator
d.) is an ideal rectifiers of high frequency signals
15. In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the
value of VCE (Q) should be approximatelya.)
0.1V
b.) 5V
c.) 10V
d) V
16. In a FET the electrode, which corresponds to collector in bipolar transistor, is –
a.) source
b.) drain
c.) gate
d.) none
17. The device which acts like an NPN and a PNP transistor connected base to base and
emitter to collector is –a.) Triacb.) UJT
c.) Diac
d.) SCR
18. A typical optical fibre has –
a.) High refractive index core and low refractive index cladding
b.) Low refractive index core and high refractive index cladding
c.) Both a and b
d.) None
19. In the following figure circuit diagram of an op-amp based is shown. The ratio is
equal to –
a.) 9
b.) 11
c.) 10
d.) 21
20. When a loud speaker is connected across the terminals A and B of the network shown in
the fig. then its impedance to obtain maximum power dissipation in it will be –
a.) 3 – j1
b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
21. In the lattice network, the value of R for the maximum power transfer to the load –
a.) 5
b.) 6.5
c.) 8
d.) 9
22. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (Z0 is the characteristic impedance, √ is the propagation constant and l is the
length of the line-a.) Z0 cot h √lb.) Z0 cot √l
c.) Z0 tan h.√ l
d.) Z0 tan √l
23. The approximate thickness of the radome wall should be –a.) λb.) λ/4
c.) λ/2
d.) λ/8
24. A relatively permanent information is stored in
a. ) ROM
b.) RAM
c.) PROM
d.) Volatile memory
25. The rise time of the RC network shown in the given figure is approximately equal to –
b.) RC
c.) 2RC
d.) 4RC
26. If in the network shown in the fig. initially a steady state is attained by closing the switch
‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will
be – a.) cos50tA
b.) 2A
c.) 2cos100tA
d.) 2sin50tA
27. When the π network of figure – I and T-network of figure – II are equivalent then the
values of R1, R2 and R3 will be respectively – a)
9, 6 and 6
b.) 6, 6 and 9
c.) 9, 6 and 9
d.) 6, 9 and 6
28. When the impedance matrices of a two port networks are given by and ,
then if these two networks are connected in series then the impedance matrix of the
resulting two-port network will be –
d.) indeterminate
29. Joule/coulomb is the unit of - a.) Electric field potential b.) Potential
c .) Charge
d.) None of the above
30. The electric field line and equipotential linesa.)
Are parallel to each other
b.)Are one and same
c.) Cut each other orthogonally
d.)Can be inclined to each other at any angle
31. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (When Z0 is the characteristic impendence γ is the propagation constant and L is
the length of the line
32. When two equal positive point charges are placed along X- axis at X1 and –X1
respectively then the electric field vector at a point P on the positive Y-axis will be
directeda.)
In the +x direction
b.) In the –x direction
c. ) In the +y direction
d.) In the –y direction
33. The directions of and in TEM mode transmission line with respect to the direction of
propagation area.)
Both and are transverse to the direction of propagation
b.) is and are transverse and h has a component in the direction of propagation
c.) is entirely transverse and has a component in the direction of propagation
d. ) is entirely transverse and has a component in the direction of propagation
34. The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will bea.)
TM01
b.)TE10
c.) TM112
d.)TE11
35. When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all
directions then at a distance d sufficiently far from the source in plane the electric field E
should be related to p and d as –
36. . When a dipole antenna was radiating with some excitation in free space radiating a
certain amount of the power v if then this antenna is immersed in a lake where water is
non-dissipative but has a dielectric constant of 81, then the radiated power with the same
excitation will be
a.) Decrease to finite non-zero value
b.)Remain the same
c. )Increase
d.)Decrease to zero
37. When a (75 – j40) load is connected to a coaxial line of Z0 = 75  at 6MHz then the
load matching on the line can be accomplished by connectinga.)
A short – circuited stub at the load
b.)An inductance at the load
c. )A short circuited stub at a specific distance from the load
d.)none of the above
38. As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more
accurate
c.) equally accurate
d.) none.
39. When a signal of 10 mV at 75 MHz is to be measured then which of the following
instruments can be used –a.) VTVMb.) Cathode ray oscilloscope
c.) Moving iron voltmeter
d.) Digital multimeter
40. Which of the following statement is true about two wattmeter method for power
measurement in three phase current ?a.) power can be measured using two wattmeter
method only for star connected three phase circuits.b.) when two meter show indentical
readings, in the power factor is 0.5.
c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the
power factor is zero –
41. When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap
of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.)
11.1b.) 44.2
c.) 52.3
d.) 66.3
42. The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as
frequency increases
c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
43. When a generator of internal impedance and operating at 1GHz feeds a load via
a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed
line is –a.) 0.5b.) 1.5
c.) 2.5
d.) 1.75
44. The coding system typically used in digital telemetry is –a.) PPM (pulse position
modulation)b.) PAM (pulse amplitude modulation)
c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
45. Radiation pyrometers are used for the measurement of temperature in the range of –
a.) -2000C to 5000C
b.) 00C to 5000C
c.) 5000C to 12000C
d.) 12000C to 25000C
46. In the given figure band structure is shown. It is of –
a.) Gallium Avesenide (GaAs)
b.) Silicon (Si)
c.) Copper (Cu)
d.) Germanium (Ge)
47. When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n
junction is –
a.) 1
b.) 2
c.) 3
d.) 4
48. The circuit symbol for a GTO is
a. b.
c. d.
49. In the given fig. mark out the type of Cyclo converters
a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device
In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the
switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.
a.) 400 A, 15.707 mS
50. b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS
51. 50. In the given circuit the maximum current in the main SCR M can bea.)
200 A
b.) 170.7 A
c.) 141.4 A
d.) 70.7 A
52. The transfer function of an amplifier is given by The
high 3-db frequency of the amplifier will approximately
a.) 5850 KHZ
b.)585 KHZ
c.) 5850 HZ
d.)585HZ
53. In comparison to full wave rectifier with two diodes the four divide bridge rectifier has
the dominant advantage of -
a). Higher current carrying
b.)Lower ripple factor
c.) Higher efficiency
d.)Lower peak increase voltage require
54. Power output increase in a class-c amplifiera.)
If the conduction angle decrease
b).If the conduction angle increase
c.) Are not governed by the conduction angle
d.)None of the above
55. A transistor with hie = 1.5 k and hfe = 75 is used in an emitter follower circuit where R1
and R2 are used for normal biasing . Approximate value of it’s current amplification isa.)
75b.)76
c.)75/76
d.)-75
56. Amplifier of class B has high theoretical efficiency of 78.5 percent becausea.)
It is biased almost to saturation
b.)Its quiescent current is low
c.)It’s output is an exact replica of it’s input
d.)It is biased well below cut off
57. The coupling that produces minimum interference with frequency response isa.)
Direct coupling
b.)Impedance coupling
c.) R C coupling
d.)Transformer coupling
58. In the circuit shown in the given figure Rf provides
a.) Current series feedback
b.)Current shunt feedback
c.) Voltage series feedback
d.)Voltage shunt feedback
59. Mark the correct relation for the junction transistor
60. Data in the serial form can be converted into parallel form by using –a.) PISO shift
registerb.) SOIP shift register
c.) SIPO shift register
d.) POIS shift register
61. PROMs are used to store-a.) bulk informationb.) information to be accessed rarely
c.) sequence information
d.) relatively permanent information
62. The horizontal axis in a 3 bit unipolar D/A converter represents-a.) Output bit
combinationb.) analog output voltage
c.) input bit combination
d.) none of the above
63. ‘Not allowed’ condition in NAND gate SR flip flop is –a.) s = 0, R = 0b.) s = 1, R = 1
c.) s = 0, R = 1
d.) s = 1, R = 0
64. Name the fastest logic family-a) TTLb.) RTL
c.) DCTL
d.) ECL
65. Equation corresponding to De Morgan’s theorem in Boolean Algebra is – a.) (A+B)
(A+B) = AA + AB + BA + BB
c.) A + AB = A
d.) None of the above
66. In the given fig find radix of the system –
a.) 2
b.) 4
c.) 6
d.) 8
67. Modems are used for data transmission telephone lines to –a.) increase the transmission
capacityb) improve noice performance
c.) incorporate error control coding
d.) eliminate dc component in the transmitted signal
68. The figure of a control system is shown. The maximum value of gain K for which the
system is stable is- a.)
b.) 3
c.) 4
d.) 5
69. Identify the example of open-loop system-a.) A windscreen wiperb.) Aqualung
c.) Respiratory system of an animal
d.) A system for controlling Anti-rocket missiles.
70. Consider the following expressions indicating the step or impulse response of an initially
relaxed control system-1. (5 – 4e-2+) u(t)2. (e-2t +5) (u(t))
3 .ς(t) + 8e-2t u(t)
4 . ς(t) + 4e-2t 4(t)
Those which correspond to the step and impulse response of the same system includea.)
1&3
b.) 1&4
c.) 2&4
d.) 1&4
71. A system is described by
To test its stability by Lyapunov’s method the following V functions are considered.
Mark the most suitable V-function in this casea.)
Only V1
b.) Only V2
c.) Both V1 and V2
d.) Neither V1 nor v2
72. Identity the polar plot of a typical type zero system with open loop transfer function
73. The scattering matrix of a magic –tee shown in the given figure is-
74. Which is the following relate to rational transfer function of a system-1. Ratio of Fourier
transform of output to input with zero initial conditions.2. Ratio of Laplace transform of
output to input with zero initial conditions.
3. Laplace transform of system impulse response.
4. Laplace transform of system unit step response select the correct answer using the
codes given below.
Codes
a.) 1 and 4
b.) 2 and 3
c.) 1 and 3
d.) 2 and 4
75. For the signal g (t) – 10 cos (50 pt) cos2 (150at)The Nyquist sampling state in t seconds
isa.) 150 samples per second
b.) 200 samples per second
c.) 300 samples per second
d.) 350 samples per second
76. In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must
lie between – MHz.a.) 34 and 106b.) 52. And 88
c.) 106 and 142
d.) 34 and 142
77. Radar used to eliminate clutter in navigational application is –a.) Pulse radarb.) Tracking
radar
c.) MTI radar
d.) Mono pulse radar
78. The 1.55 mm windows is not yet in use with fiber optic systems because –a.) The
attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mm
c.) Suitable laser devices have not yet been developed
d.) It does not lend itself to wavelength multiplexing
79. Pre-emphasis in FM systems involves-a.) Compression of the modulating signalb.)
Expansion of the modulating signal
c.) Amplification of lower frequency components of the modulating signal.
d.) Amplification of higher frequency components of the modulating signal.
80. In a terrestrial microwave system transmission of signals is achieved through-a.)
reflection from the ionosphereb.) line of sight mode
c) reflection from the ground
d.) diffraction from the stratosphere.
81. Casse grain feed is used with a parabolic reflector toa.) increase the gain of the systemb).
increase the bandwidth of the system
c.) reduce the size of the main reflector
d.) allow the feed to be placed at a convenient point.
82. In most microwave communication link rain drop attenuation is caused due to-a.)
scattering of microwaves by water drops of specific size.b) scattering of microwaves by a
collection of droplets acing as a single body.
c.) absorption of microwaves by water and consequent heating of the liquid
d.) absorption of the microwaves by water vapor in the atmosphere.
83. Circuit in the given figure represents. – a.) an astable
multivibrator
b.) A monostable multivibrator
c.) Voltage controlled oscillator
d.) Ramp generator
84. . . D = r is-a.) Maxwell’s 1st equationb.) Maxwell’s II equation
c.) Maxwell’s III equation
d.) Maxwell’s IV equation
85. In a rectangular wave-guide which TM mode exists-a.) TM00b.) TM01
c.) Tm10
d.) TM11
86. In directional coupler a portion of power two velliry fram port 1) to port 2) is coupled
to.a). port 4b). port 3
c.) port 2.
d.) port 3 & 4.
87. For high power i.e. 10 w to 50 kw measurement –
a.) Barometer are used
b.) Thermisters are used
c.) Calorimetric technique
d.) Calorimetric watt meter technique used
88. The difference between TWT & klystron is –
a.) In TWT electrons are in contact with RF field for long time & in klystron for
short time
b.) In klystron electrons are in contact with RF field for long time & in TWT for short
time
c.) In klystron there is no contact in RF field & electrons while in TWT there is contact
d.) In TWT phase is no contact is RF field & electrons while in klystron there is contact
89. Which one is most suitable for transmission through wave guidea.)
Hown antennas
b.) Bioconical antennas
c.) helical antenna
d. )Discone
90. The skip distance of microwave is given by –
a.)
b. )
c.)
d.)
91. How many general purpose registers 8085mpa.)
4
b.) 6
c.) 8
c.) 10
92. 8085 mP has no. of addressing modesa.)
2
b.) 3
c.) 4
d.) 5
93. What will be status of z and c y flag after execution of SUB A instruction
a.) z = 0, cy = 0
b.) z = 0, cy = 1
c.) z = 1, cy = 0
d.) z = 1, cy = 1
94. Microprocessor accept interrupt only if.
a.) interrupt flip flop disabled.
b.) when INTA signal is low.
c. ) interrupt flip flop enabled.
d.) none of above.
95. Microprogramming is a technique
a.) for programming the microprocessor
b.) for writing small programs efficiently
c.) for programming the control steps of computer
d.) for programming o/p / i/p
96. High level programs like C are converted into machine language with the help ofa.)
interpreterb.) compiler
c.) operating
d.) system
97. (10110011)2 = (?)8a.) 253b.) 263
c.) 273
d.) 283
98. A Not gate at the output of AND gate converts AND gate into-a.) NANDb.) NOR
c.) AND
d.) NOPE.
99. The O/P of a logic gate is the gate must be-a.) ANDb.) OR
c.) NAND
d.) X-OR
100. A symbol of JK flip flop is-
101. A demultiplener-a.) has multiple i/p and single o/pb.) has multiple i/p and
multiple o/p
c.) has multiple i/p and multiple o/p
d.) has single i/p and single o/p
102. . Which of the following best describes the authour`s attitude toward fairy tales
?a.) fascinationb.) open approval.
c.) Indulgent tolerance.
d.) Scornful.
103. What type of sentence is this ?Hurray! We won the matcha.) Exclamatory
b.) assertive
c.) Negative
d.) Affirmative
104. Before which of the following word will you put ‘a’a.) hourb.) M. A.
c.) Umbrella
d.) Man
105. The noun form of ‘fresh’ is –a.) freshlyb.) freshen
c.) fresheners
d.) fresh itself
106. The word ‘clang’ is an example of –a.) Simileb.) inversion
c.) onomatopoeia
d.) irony
107. The Forbes magazine acclaimed Azim Premji as richest India’s is the chairman
of-a.) Pentafour softwareb) Infosys
c.) IBM
d.) Wipro
108. Bharat Ratna award for the year 2001 goes to-a.) Lata Mangeshkar and Zakeer
Hussainb.) Zakeer Hussain and Bismillah Khan
c.) Bismillah Khan and Lata Mangeshkar
d.) Lata Mangeshkar and Ustad Amzad Ali Khan
109. Mr. George W-Bush takes over as —— President of the united states of America
succeeding Mr. Bill Clinton-a.) 42nd
b.) 43rd
c.) 40th
d.) 45th
110. New Chief Minister of Pondicherry is-a.) T. Venkat Naidub.) K. Hari Harh
c.) N. Rengaswany
d.) M. Mudliar
111. No court has the jurisdiction to interfere with the election process once set in
motion by the Election commission. This is enshrined in Article-a.) 311b.) 329
c.) 356
d.) 365
112. Ostrich is a-a.) Running birdb.) Flying bird
c) Swimming bird
d.) Migratory bird
113. The main atmospheric gas responsible for green house is-a.) Oxygenb.) Nitrogen
c.) Ozone
d.) Carbon-dioxide
114. Which of the following is not a Kharif Crop-a.) Riceb.) groundnut
c.) Sugarcane
d.) gram
115. The function of World Bank is to-a.) Help in reconstruction and development
of world economyb.) Facilitate poor countries to trade on concessional rates
c.) Promote growth of international trade and equilibrium in balance of payments
d.) Ease trade barriers and establish rule of fair trade
116. Speed of sound is maximum in-a. )Waterb.) Air
c.) Steel
d.) Vacuum
117. “Long years ago we made a trust with destiny.” Whose words are these-a.)
Subhash Chandra Boseb.) Jawaharlal Nehru
c.) Lajpat Rai
d.) Bhagat Singh
118. Durand cup is associated with-a.) Hockeyb.) Tennis
c.) Football
d.) Badminton
119. Rabindranath Tagore was awarded the Nobel Prize in literature in the year.a.)
1908b.) 1910
c.) 1913
d.) 1914
120. India successfully conducted its first underground nuclear experiment at Pokhran
in Rajas than on-a.) May 18, 1975b.) May 20, 1974
c) May 17, 1974
d.) May 17, 1974
121. An emergency loan of $ 500 million to help reconstruct infrastructure in earth
quake devastated Gujarat approved by-a.) Asian development Bankb.) World Bank
c.) Swiss Bank
d.) Reserve Bank of India

SIR this is kuldeep, please send me syllabus for engineer trainee of EC on my email [email protected]

please send me BHEL paper for electronics and communication engineering

send answers for the above questions

SIR this is surender khatri, please send me syllabus for Supervisor Trainee (Engineering)

of ECE on my email [email protected]

Originally Posted by Unregistered

good morning , i have submitted bhel online application with OBC cast, but here due to internet problem i am not
getting my cast certificate at now .so my question is can i send my document without cast certificate or you may consider it as GEN..

vthout cast certificate they reject the registration and u ill nt gt d hall tickt 4 xam

send me some bhel electronics engineering training model ques with answer

SIR this is divya.please send me engineer trainee sample question paper in the discipline of ECE at [email protected]

send answers for above questions

i want BHEL previous years electronics question papers with answers for engineer trainee

this is v.saravanan i am a electronic student i want the syllabus of electronic major and also some old question papers sir u kindly send all the details for following mail id [email protected]

this is Kohila.first time i made some mistake while filling up the educational details.I got one ACK no.Afterwards I corrected the mistake and i got another ACK no.So I have to take a print out of second or both..

Sir Am in urgent need of Engineer trainee model question paper of Mechanical Branch.

Sir Am in urgent need of Engineer trainee model question paper of ELECTRICAL Branch.FOR Bhel company.

Need answers for the above sample questions

i have given my name as A.karthika and sent to BHEL with BHELchallan copy........ now i noticed that my name is written as karthika.A in my certificates....... can i apply fresh application with old bank journal number (but i have sent challan copy with old acknowledgement slip) orelse i have to pay amount again and apply???? please reply me soon sir........

Sir i applied for engineer trainee for electronics in BHEL.Pls send me model ques paper to my mail id [email protected]

I NEED ENGG MODEL
\

SIR this is rajitha.please send me engineer trainee sample question paper in the discipline of ECE at [email protected]
Reply With Quote

Source: http://entrance-exam.net/forum/general-discussion/bhel-engineer-trainee-model-question-paper-electronics-major-39635.html#ixzz1Vq3niHFG

Sir i have applied for engineer trainee for electronics and communication in BHEL.Pls pls pls send me model ques paper to my mail id [email protected]'ll be very thankful if u send d model paper with answers

Respected sir,
This is R.PUSHPAVALLI finished B.TECH(ECE) and applied for engineer trainee of BHEL.I have sent the community certificate and BHEL challan copy without attaching acknowledgement copy on 18th august 2011.And sent the acknowledgement copy separately on 20th august 2011.But while checking the latest status in BHEL site,it is displaying that they didn receive my acknowledgement slip,and the online submission was successful.will you consider my application and send me the hall ticket.
pls kindly do the needful and reply me to this mail i.d [email protected] please.

Thanking you sir,
yours faithfully,
R.PUSHPAVALLI

sir this is karan kumar, i want to know what is the percentage requirment in degree for aplicable in bhel for sc candidae .

this is renuga.i need model question papers for engineer trainee exam in electronics stream

can u send preparation material for supervisor trainee for electronics?pls.....

iam in need of bhel et ece syllabus question papers with solutions

Hi friends this nadhiya please send me engineer trainee model question paper of electronics to this mail [email protected]

Please upload the answers also

Hi dear,

here is the model question paper. check it.

BHEL Model question paper(Answers Updated)
1. For ELECTRICAL & ELECTRONICS with answers(bolded words)
2. When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing
through it dissipates 1000 watts then which of the following will have least value in ohms
a.) Resistanceb.) Reactance
c.) Impedance
d.) None
3. Oscillator crystal are made of –
a.) Silicon
b.) Germanium
c.) Quartz
d.) None
4. For small size, high frequency coils, the most common core material is-a. )Airb. )Ferrite
c.) Powdered ion
d.) Steel
5. If we have a parallel plate capacitor of plate area ‘A’ and plate separatoin t and having a
capacity C and a metallic plate r of area A and of negligible thickness is introduced in the
capacitor at a distance from either of the two plates as shown in the given
figure then the capacity of the capacitor will become –
a.)
b.) C
c.) 2C
d.) 4C
6. A superconductor is a –
a.) A material showing perfect conductivity and Meissner effect below a critical
temperature
b.) A conductor having zero resistance
c.) A perfect conductor with highest di-magnetic susceptibility
d.) A perfect conductor which becomes resistance when the current density through it
exceeds a critical value
7. When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF
capacitor then the self capacitance of the inductor would be –
a) 8.05 pF
b) 10.05pF
c.) 16.01pF
d.) 20.01pF
8. Sparking occur when a load is switched off because the circuit has high –
a.) Inductance
b.) Capacitance
c.) Resistance
d.) None
9. Sparking between contacts can be reduced by inserting a –
a.) Resistance in the line
b.) Capacitor in series with contacts
c.) Capacitor in parallel with contacts
d.) None
10. RF amplifier of an A.M. receiver is normally biased in –
a.) Class ‘A’
b.) Class ‘b’
c.) Class ‘C’
d.) None
11. The value of gate voltage for the operation of enhancement of only N channel MOSFET
has to be –
a.) High positive
b.) High negative
c.) Low positive
d.) Zero
12. The input gate current of a FET is –
a.) a few microamperes
b.) negligibly small
c.) a few milliamperes
d.) a few amperes
13. In the following fig. with R = 30k, the value of current through 2 K resistor is –
a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA
14. A step recovery diode –
a.) has on extremely short recovery time
b.) conducts equally well in both directions
c.) is mainly used as a harmonic generator
d.) is an ideal rectifiers of high frequency signals
15. In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the
value of VCE (Q) should be approximatelya.)
0.1V
b.) 5V
c.) 10V
d) V
16. In a FET the electrode, which corresponds to collector in bipolar transistor, is –
a.) source
b.) drain
c.) gate
d.) none
17. The device which acts like an NPN and a PNP transistor connected base to base and
emitter to collector is –a.) Triacb.) UJT
c.) Diac
d.) SCR
18. A typical optical fibre has –
a.) High refractive index core and low refractive index cladding
b.) Low refractive index core and high refractive index cladding
c.) Both a and b
d.) None
19. In the following figure circuit diagram of an op-amp based is shown. The ratio is
equal to –
a.) 9
b.) 11
c.) 10
d.) 21
20. When a loud speaker is connected across the terminals A and B of the network shown in
the fig. then its impedance to obtain maximum power dissipation in it will be –
a.) 3 – j1
b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
21. In the lattice network, the value of R for the maximum power transfer to the load –
a.) 5
b.) 6.5
c.) 8
d.) 9
22. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (Z0 is the characteristic impedance, √ is the propagation constant and l is the
length of the line-a.) Z0 cot h √lb.) Z0 cot √l
c.) Z0 tan h.√ l
d.) Z0 tan √l
23. The approximate thickness of the radome wall should be –a.) λb.) λ/4
c.) λ/2
d.) λ/8
24. A relatively permanent information is stored in
a. ) ROM
b.) RAM
c.) PROM
d.) Volatile memory
25. The rise time of the RC network shown in the given figure is approximately equal to –
b.) RC
c.) 2RC
d.) 4RC
26. If in the network shown in the fig. initially a steady state is attained by closing the switch
‘s’ and then if the switch is opened at t = 0, then the current i(t) through the inductor will
be – a.) cos50tA
b.) 2A
c.) 2cos100tA
d.) 2sin50tA
27. When the π network of figure – I and T-network of figure – II are equivalent then the
values of R1, R2 and R3 will be respectively – a)
9, 6 and 6
b.) 6, 6 and 9
c.) 9, 6 and 9
d.) 6, 9 and 6
28. When the impedance matrices of a two port networks are given by and ,
then if these two networks are connected in series then the impedance matrix of the
resulting two-port network will be –
d.) indeterminate
29. Joule/coulomb is the unit of - a.) Electric field potential b.) Potential
c .) Charge
d.) None of the above
30. The electric field line and equipotential linesa.)
Are parallel to each other
b.)Are one and same
c.) Cut each other orthogonally
d.)Can be inclined to each other at any angle
31. For a lossy transmission line short circuited at the receiving end, the input impedance is
given by (When Z0 is the characteristic impendence γ is the propagation constant and L is
the length of the line
32. When two equal positive point charges are placed along X- axis at X1 and –X1
respectively then the electric field vector at a point P on the positive Y-axis will be
directeda.)
In the +x direction
b.) In the –x direction
c. ) In the +y direction
d.) In the –y direction
33. The directions of and in TEM mode transmission line with respect to the direction of
propagation area.)
Both and are transverse to the direction of propagation
b.) is and are transverse and h has a component in the direction of propagation
c.) is entirely transverse and has a component in the direction of propagation
d. ) is entirely transverse and has a component in the direction of propagation
34. The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will bea.)
TM01
b.)TE10
c.) TM112
d.)TE11
35. When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all
directions then at a distance d sufficiently far from the source in plane the electric field E
should be related to p and d as –
36. . When a dipole antenna was radiating with some excitation in free space radiating a
certain amount of the power v if then this antenna is immersed in a lake where water is
non-dissipative but has a dielectric constant of 81, then the radiated power with the same
excitation will be
a.) Decrease to finite non-zero value
b.)Remain the same
c. )Increase
d.)Decrease to zero
37. When a (75 – j40) load is connected to a coaxial line of Z0 = 75  at 6MHz then the
load matching on the line can be accomplished by connectinga.)
A short – circuited stub at the load
b.)An inductance at the load
c. )A short circuited stub at a specific distance from the load
d.)none of the above
38. As compared to analog multimeters, digital multimeters are –a.) less accurateb.) more
accurate
c.) equally accurate
d.) none.
39. When a signal of 10 mV at 75 MHz is to be measured then which of the following
instruments can be used –a.) VTVMb.) Cathode ray oscilloscope
c.) Moving iron voltmeter
d.) Digital multimeter
40. Which of the following statement is true about two wattmeter method for power
measurement in three phase current ?a.) power can be measured using two wattmeter
method only for star connected three phase circuits.b.) when two meter show indentical
readings, in the power factor is 0.5.
c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the
power factor is zero –
41. When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap
of 2mm than the displacement sensitivity in pf/cm due to gap change would be –a.)
11.1b.) 44.2
c.) 52.3
d.) 66.3
42. The Q of a radio coil –a.) is independent of frequencyb.) increases monotonically as
frequency increases
c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
43. When a generator of internal impedance and operating at 1GHz feeds a load via
a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed
line is –a.) 0.5b.) 1.5
c.) 2.5
d.) 1.75
44. The coding system typically used in digital telemetry is –a.) PPM (pulse position
modulation)b.) PAM (pulse amplitude modulation)
c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
45. Radiation pyrometers are used for the measurement of temperature in the range of –
a.) -2000C to 5000C
b.) 00C to 5000C
c.) 5000C to 12000C
d.) 12000C to 25000C
46. In the given figure band structure is shown. It is of –
a.) Gallium Avesenide (GaAs)
b.) Silicon (Si)
c.) Copper (Cu)
d.) Germanium (Ge)
47. When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n
junction is –
a.) 1
b.) 2
c.) 3
d.) 4
48. The circuit symbol for a GTO is
a. b.
c. d.
49. In the given fig. mark out the type of Cyclo converters
a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device
In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the
switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.
a.) 400 A, 15.707 mS
50. b.) 50 A, 30 mSc.) 100 A, 62.828 mSd.) 400 A, 31.414 mS
51. 50. In the given circuit the maximum current in the main SCR M can bea.)
200 A
b.) 170.7 A
c.) 141.4 A
d.) 70.7 A
52. The transfer function of an amplifier is given by The
high 3-db frequency of the amplifier will approximately
a.) 5850 KHZ
b.)585 KHZ
c.) 5850 HZ
d.)585HZ
53. In comparison to full wave rectifier with two diodes the four divide bridge rectifier has
the dominant advantage of -
a). Higher current carrying
b.)Lower ripple factor
c.) Higher efficiency
d.)Lower peak increase voltage require
54. Power output increase in a class-c amplifiera.)
If the conduction angle decrease
b).If the conduction angle increase
c.) Are not governed by the conduction angle
d.)None of the above
55. A transistor with hie = 1.5 k and hfe = 75 is used in an emitter follower circuit where R1
and R2 are used for normal biasing . Approximate value of it’s current amplification isa.)
75b.)76
c.)75/76
d.)-75
56. Amplifier of class B has high theoretical efficiency of 78.5 percent becausea.)
It is biased almost to saturation
b.)Its quiescent current is low
c.)It’s output is an exact replica of it’s input
d.)It is biased well below cut off
57. The coupling that produces minimum interference with frequency response isa.)
Direct coupling
b.)Impedance coupling
c.) R C coupling
d.)Transformer coupling
58. In the circuit shown in the given figure Rf provides
a.) Current series feedback
b.)Current shunt feedback
c.) Voltage series feedback
d.)Voltage shunt feedback
59. Mark the correct relation for the junction transistor
60. Data in the serial form can be converted into parallel form by using –a.) PISO shift
registerb.) SOIP shift register
c.) SIPO shift register
d.) POIS shift register
61. PROMs are used to store-a.) bulk informationb.) information to be accessed rarely
c.) sequence information
d.) relatively permanent information
62. The horizontal axis in a 3 bit unipolar D/A converter represents-a.) Output bit
combinationb.) analog output voltage
c.) input bit combination
d.) none of the above
63. ‘Not allowed’ condition in NAND gate SR flip flop is –a.) s = 0, R = 0b.) s = 1, R = 1
c.) s = 0, R = 1
d.) s = 1, R = 0
64. Name the fastest logic family-a) TTLb.) RTL
c.) DCTL
d.) ECL
65. Equation corresponding to De Morgan’s theorem in Boolean Algebra is – a.) (A+B)
(A+B) = AA + AB + BA + BB
c.) A + AB = A
d.) None of the above
66. In the given fig find radix of the system –
a.) 2
b.) 4
c.) 6
d.) 8
67. Modems are used for data transmission telephone lines to –a.) increase the transmission
capacityb) improve noice performance
c.) incorporate error control coding
d.) eliminate dc component in the transmitted signal
68. The figure of a control system is shown. The maximum value of gain K for which the
system is stable is- a.)
b.) 3
c.) 4
d.) 5
69. Identify the example of open-loop system-a.) A windscreen wiperb.) Aqualung
c.) Respiratory system of an animal
d.) A system for controlling Anti-rocket missiles.
70. Consider the following expressions indicating the step or impulse response of an initially
relaxed control system-1. (5 – 4e-2+) u(t)2. (e-2t +5) (u(t))
3 .ς(t) + 8e-2t u(t)
4 . ς(t) + 4e-2t 4(t)
Those which correspond to the step and impulse response of the same system includea.)
1&3
b.) 1&4
c.) 2&4
d.) 1&4
71. A system is described by
To test its stability by Lyapunov’s method the following V functions are considered.
Mark the most suitable V-function in this casea.)
Only V1
b.) Only V2
c.) Both V1 and V2
d.) Neither V1 nor v2
72. Identity the polar plot of a typical type zero system with open loop transfer function
73. The scattering matrix of a magic –tee shown in the given figure is-
74. Which is the following relate to rational transfer function of a system-1. Ratio of Fourier
transform of output to input with zero initial conditions.2. Ratio of Laplace transform of
output to input with zero initial conditions.
3. Laplace transform of system impulse response.
4. Laplace transform of system unit step response select the correct answer using the
codes given below.
Codes
a.) 1 and 4
b.) 2 and 3
c.) 1 and 3
d.) 2 and 4
75. For the signal g (t) – 10 cos (50 pt) cos2 (150at)The Nyquist sampling state in t seconds
isa.) 150 samples per second
b.) 200 samples per second
c.) 300 samples per second
d.) 350 samples per second
76. In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must
lie between – MHz.a.) 34 and 106b.) 52. And 88
c.) 106 and 142
d.) 34 and 142
77. Radar used to eliminate clutter in navigational application is –a.) Pulse radarb.) Tracking
radar
c.) MTI radar
d.) Mono pulse radar
78. The 1.55 mm windows is not yet in use with fiber optic systems because –a.) The
attenuation is higher than at 0.85 mm b) The attenuation is higher than at 1.3mm
c.) Suitable laser devices have not yet been developed
d.) It does not lend itself to wavelength multiplexing
79. Pre-emphasis in FM systems involves-a.) Compression of the modulating signalb.)
Expansion of the modulating signal
c.) Amplification of lower frequency components of the modulating signal.
d.) Amplification of higher frequency components of the modulating signal.
80. In a terrestrial microwave system transmission of signals is achieved through-a.)
reflection from the ionosphereb.) line of sight mode
c) reflection from the ground
d.) diffraction from the stratosphere.
81. Casse grain feed is used with a parabolic reflector toa.) increase the gain of the systemb).
increase the bandwidth of the system
c.) reduce the size of the main reflector
d.) allow the feed to be placed at a convenient point.
82. In most microwave communication link rain drop attenuation is caused due to-a.)
scattering of microwaves by water drops of specific size.b) scattering of microwaves by a
collection of droplets acing as a single body.
c.) absorption of microwaves by water and consequent heating of the liquid
d.) absorption of the microwaves by water vapor in the atmosphere.
83. Circuit in the given figure represents. – a.) an astable
multivibrator
b.) A monostable multivibrator
c.) Voltage controlled oscillator
d.) Ramp generator
84. . . D = r is-a.) Maxwell’s 1st equationb.) Maxwell’s II equation
c.) Maxwell’s III equation
d.) Maxwell’s IV equation
85. In a rectangular wave-guide which TM mode exists-a.) TM00b.) TM01
c.) Tm10
d.) TM11
86. In directional coupler a portion of power two velliry fram port 1) to port 2) is coupled
to.a). port 4b). port 3
c.) port 2.
d.) port 3 & 4.
87. For high power i.e. 10 w to 50 kw measurement –
a.) Barometer are used
b.) Thermisters are used
c.) Calorimetric technique
d.) Calorimetric watt meter technique used
88. The difference between TWT & klystron is –
a.) In TWT electrons are in contact with RF field for long time & in klystron for
short time
b.) In klystron electrons are in contact with RF field for long time & in TWT for short
time
c.) In klystron there is no contact in RF field & electrons while in TWT there is contact
d.) In TWT phase is no contact is RF field & electrons while in klystron there is contact
89. Which one is most suitable for transmission through wave guidea.)
Hown antennas
b.) Bioconical antennas
c.) helical antenna
d. )Discone
90. The skip distance of microwave is given by –
a.)
b. )
c.)
d.)
91. How many general purpose registers 8085mpa.)
4
b.) 6
c.) 8
c.) 10
92. 8085 mP has no. of addressing modesa.)
2
b.) 3
c.) 4
d.) 5
93. What will be status of z and c y flag after execution of SUB A instruction
a.) z = 0, cy = 0
b.) z = 0, cy = 1
c.) z = 1, cy = 0
d.) z = 1, cy = 1
94. Microprocessor accept interrupt only if.
a.) interrupt flip flop disabled.
b.) when INTA signal is low.
c. ) interrupt flip flop enabled.
d.) none of above.
95. Microprogramming is a technique
a.) for programming the microprocessor
b.) for writing small programs efficiently
c.) for programming the control steps of computer
d.) for programming o/p / i/p
96. High level programs like C are converted into machine language with the help ofa.)
interpreterb.) compiler
c.) operating
d.) system
97. (10110011)2 = (?)8a.) 253b.) 263
c.) 273
d.) 283
98. A Not gate at the output of AND gate converts AND gate into-a.) NANDb.) NOR
c.) AND
d.) NOPE.
99. The O/P of a logic gate is the gate must be-a.) ANDb.) OR
c.) NAND
d.) X-OR
100. A symbol of JK flip flop is-
101. A demultiplener-a.) has multiple i/p and single o/pb.) has multiple i/p and
multiple o/p
c.) has multiple i/p and multiple o/p
d.) has single i/p and single o/p
102. . Which of the following best describes the authour`s attitude toward fairy tales
?a.) fascinationb.) open approval.
c.) Indulgent tolerance.
d.) Scornful.
103. What type of sentence is this ?Hurray! We won the matcha.) Exclamatory
b.) assertive
c.) Negative
d.) Affirmative
104. Before which of the following word will you put ‘a’a.) hourb.) M. A.
c.) Umbrella
d.) Man
105. The noun form of ‘fresh’ is –a.) freshlyb.) freshen
c.) fresheners
d.) fresh itself
106. The word ‘clang’ is an example of –a.) Simileb.) inversion
c.) onomatopoeia
d.) irony
107. The Forbes magazine acclaimed Azim Premji as richest India’s is the chairman
of-a.) Pentafour softwareb) Infosys
c.) IBM
d.) Wipro
108. Bharat Ratna award for the year 2001 goes to-a.) Lata Mangeshkar and Zakeer
Hussainb.) Zakeer Hussain and Bismillah Khan
c.) Bismillah Khan and Lata Mangeshkar
d.) Lata Mangeshkar and Ustad Amzad Ali Khan
109. Mr. George W-Bush takes over as —— President of the united states of America
succeeding Mr. Bill Clinton-a.) 42nd
b.) 43rd
c.) 40th
d.) 45th
110. New Chief Minister of Pondicherry is-a.) T. Venkat Naidub.) K. Hari Harh
c.) N. Rengaswany
d.) M. Mudliar
111. No court has the jurisdiction to interfere with the election process once set in
motion by the Election commission. This is enshrined in Article-a.) 311b.) 329
c.) 356
d.) 365
112. Ostrich is a-a.) Running birdb.) Flying bird
c) Swimming bird
d.) Migratory bird
113. The main atmospheric gas responsible for green house is-a.) Oxygenb.) Nitrogen
c.) Ozone
d.) Carbon-dioxide
114. Which of the following is not a Kharif Crop-a.) Riceb.) groundnut
c.) Sugarcane
d.) gram
115. The function of World Bank is to-a.) Help in reconstruction and development
of world economyb.) Facilitate poor countries to trade on concessional rates
c.) Promote growth of international trade and equilibrium in balance of payments
d.) Ease trade barriers and establish rule of fair trade
116. Speed of sound is maximum in-a. )Waterb.) Air
c.) Steel
d.) Vacuum
117. “Long years ago we made a trust with destiny.” Whose words are these-a.)
Subhash Chandra Boseb.) Jawaharlal Nehru
c.) Lajpat Rai
d.) Bhagat Singh
118. Durand cup is associated with-a.) Hockeyb.) Tennis
c.) Football
d.) Badminton
119. Rabindranath Tagore was awarded the Nobel Prize in literature in the year.a.)
1908b.) 1910
c.) 1913
d.) 1914
120. India successfully conducted its first underground nuclear experiment at Pokhran
in Rajas than on-a.) May 18, 1975b.) May 20, 1974
c) May 17, 1974
d.) May 17, 1974
121. An emergency loan of $ 500 million to help reconstruct infrastructure in earth
quake devastated Gujarat approved by-a.) Asian development Bankb.) World Bank
c.) Swiss Bank
d.) Reserve Bank of India

Thanks

please send me the previous exam papers of BHEL for supervisor trainee also the syllabus of same for electronics and telecommunications
my email id is [email protected]

good evng sir,iwant what is syllobus for bhel.plz.send .it is urgent

Originally Posted by dina09

hai friends,
this is dinesh. the answer for above questions are in the following link
http://senthil4u.wordpress.com/2009/09/08/bhel-modern-question-paper/

thank you...

Sir, please send me answers for above question papers.........